Changing switch-off function
To change the switch-off function (activated ↔
deactivated), the jumper J1 must be moved into
the corresponding position.
disable:
J1 Pos. 1
1
4 3 2
aneble:
J1 Pos. 1-2
1
4 3 2
If the switch-off function is disabled, the
RCL07 can not be switched off via the
button .
Changes to the switch-off or acknow
-
ledgment function can only be made
when the power is off.
Changing the acknowledge function
To change the acknowledge function (activated ↔
deactivated), the jumper J2 must be moved into
the corresponding position.
activate: J2 Pos. 4
deactivate: J2 Pos. 3+4
2
Operation
[Press button]
Display LED RCL07
Description
Programming a call transmitter
The call transmitter is used to send out a care call.
Tx
<1,6 s
R
1
2
3
4
J2
J1
Q/S
R
1x
R
BA
EIN/AUS
2x
R
BA
IMPULS
3x
R
Betriebs-
bereitschaft
R
<1,6 s
R
<1.6 s
LED
R
flashes slowly
(1x|break|1x| ...)
OM
ON/OFF
selected
R
<1.6 s
LED
R
flashes in cycles of two
(2x|break|2x| ...)
OM
PULSE
selected
The receiver is in programming mode for approx.
30 seconds. Programming the transmission code
during this period, after the period has expired, the
receiver changes to operation mode.
Tx <1.6 s
LED
R
illuminates for
approx. 4 s
The transmission code is transmitted. The operat-
ing mode set at the receiver is accepted with the
save procedure and is applicable for the trans-
mission code saved. Subsequently, the receiver
changes to operation mode.
Flashes the LED
R
quickly for approx. 4 seconds,
all 32 memory spaces are allocated.
J2
J1
1
4 3 2
1
4 3 2
mission code again.
Installation
Caution!
Make sure there is no interference with
the wireless connection. Do not mount the device
in a distribution box, in metal casings, in direct
proximity to large metal objects, on the floor or
close to it.
1. Remove the housing cover.
2. Use jumper J1 to select whether the switch-
off function should be disabled or enabled and
jumper J2 if the acknowledge function should
be activated or deactivated.
The receiver is supplied with deactivated
Switch-Off Function and activated Acknow
-
ledgment Function.
3. Connect the supply voltage and the protec
-
tive low voltage loads (see Fig. 1). The LED
will light up in green.
4. Transfer the codes of the transmitters to the
receiver (see section “Programming the trans-
mitter“).
5. Re-install the housing cover.
Notice:
The receiver cannot be programmed
with the learn button PTx of the Easywave ra
-
dio transmitters.
PROGRAMMING TRANSMITTERS
Each type of transmitter can only be programmed
into the RCL07 once!
If e.g. for transmitters with 2-button operation, the
transmission code A or B is programmed in the
receiver, the buttons C and D can not be used in
this RCL07.
A transmitter can only ever be used for ONE func
-
tion.
START-UP
Q/S
programming button
Q/S
R
programming button
R
Tx
transmitter button
OM
Operating mode
ON/OFF
PULSE
Operating mode
<1.6 s
<1.6 s
1
2
3
4
J2
J1
NC1 CO
M
NO
1
NO
2
NC1, COM,
NO1, NO2:
CO/NO
+
,
-
Power Supply
12-24V DC
Jumper J1
Jumper J2
Fig. 1
PROGRAMMING
