ELCOM Uniq Display 15

introduction

Thank you for choosing the Uniq Display. Please read this user manual before you begin using the equipment 
in order to become familiar with its features and functions. Also keep this user manual for future use. It will help 
you solve problems that may arise.

imPortant notice

•   Do not leave switched-on equipment unattended!
•   Install the product in a place where it will not be exposed to direct sunlight, unusual changes in tem

-

perature (below 0°C and over 40°C) or high humidity. Installation in an unsuitable place could cause 
damage to the casing and electrical components

•   When transferring the product between environments with different temperatures, do not switch it on for 

at least 60 minutes.

•   Never use aggressive cleaning solutions when cleaning the product surface. The use of unsuitable 

cleaning solutions can cause damage to the product.

•   If the product is not functioning properly, turn to an authorized service technician. Do not attempt to 

repair the product yourself. Never open the product casing!

•   When plugging in this equipment always use the power adapter supplied or one exclusively authorized 

by the seller. The use of another resource can lead to damage to the source or the product.

•  

notice:

 The adapter is specified for interior use only!

•   The use of sharp objects for handling the touch screen panel can seriously damage or destroy it.
•   This product cannot be cleaned using a strong stream of spraying water, nor can it be submerged in 

water.

•   Some electrical equipment producing interference and connected to the same electrical circuit can 

cause the improper functioning of the equipment. In such cases, use a special anti-jamming device 
recommended by the manufacturer.

•   To fully disconnect the device from the electrical network unplug it from the electrical socket.
•   The manufacturer is not responsible for any damage caused to the product in the case of improper 

maintenance or use in a different  manner than is described in these instructions.

• 

The symbol (a crossed-out wastebasket) on the product or its packaging means that the product, 
upon completion of its lifespan, should not be disposed of in common household waste, but 
must be taken to a collection point designated for the collection of worn-out electrical and 
electronic appliances. Proper liquidation of this product can help preserve natural resources 
and helps in the prevention of negative impacts on the environment and human health.

• 

The product contributes to environmental protection through the use of lead-free technology 
during its production.

18

Introduction

&/(-*4)

Summary of Contents for Uniq Display 15"

















Reviews: