ELCA AR BRAVO-FUNK-915 User Manual Download Page 27

ENG man BRAVO-FUNK-915 00

 

BRAVO-FUNK-915 Radio remote control system

- Page 21 -

ENGLISH

7.4  CHARGING CYCLE FUNCTIONAL CONTROL

Follow the diagram below (starting from the top left corner) to solve or identify the problem.

IS THE RED 

CHARGE LED ON?

CLEAN THE ELECTRICAL 

CONTACTS ON THE 

BATTERY AND ON THE 

BATTERY CHARGER 

IS THE RED 

CHARGE LED ON?

NO

YES

CHARGING CYCLE 

COMPLETED

MAKE SURE 

TEMPERATURE 

GOES BACK WITHIN 

ALLOWED 

RANGE (0-45 °C)

YES

YES

IS THE RED 

CHARGE LED 

FLASHING?

NO

YES

IS THE AMBIENT 

TEMPERATURE 

BETWEEN 0 - 45°C?

NO

YES

IS THE GREEN 

POWER LED ON?

SI

NO

CHECK CONNECTION 

OF BATTERY CHARGER 

POWER SUPPLY UNIT

IS THE GREEN 

POWER LED ON?

CHECK THE FUSE AND 

REPLACE IT WITH 

ANOTHER IDENTICAL 

ONE IF DEFECTIVE

YES

NO

IS THE GREEN 

POWER LED ON?

YES

NO

CONTACT 

ASSISTANCE 

SERVICE

WAIT FOR CHARGING 

TO LOAD

NO

IS THE RED 

CHARGE LED OFF?

BATTERY FAILURE. 

REPLACE THE BATTERY

IS THE RED 

CHARGE LED 

FLASHING? 

YES

NO

HAVE MORE THAN 

4 HOURS PASSED?

YES

NO

NO

CONTACT 

ASSISTANCE 

SERVICE

CONTACT 

ASSISTANCE 

SERVICE

Summary of Contents for AR BRAVO-FUNK-915

































Reviews: