Elba EDW-1290 Instruction Manual Download Page 6

4

Always use salt intended for use with dishwashers.

The salt container is located beneath the lower rack and should be filled as follows:

Unscrew the cap from the salt container.

There is a ring on the container with an arrow on it (see Figure to the side), if

necessary, rotate the ring in the anticlockwise direction from the "-" Setting
toward the "+" sign, based on the hardness of the water being used.It is
recommended that adjustments should be made in accordance with the following

schema:

1

2

1.

2.

The salt container must be refilled when the salt warning light comes on. Though the salt container is filled

enough, the indicator light may not black out before the salt fully dissolve.
If there are spills of the salt, a soak program could be run to wipe them out.

The hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits will form on the dishes

and utensils.

The appliances is equipped with a special softener that uses a salt specifically designed to eliminate lime and minerals from the

water.

The dishwasher is designed to allow for adjusting the amount of salt consumed based on the hardness of the water used.

This is intended to optimize and customize the level of salt consumption so that the salt consumption could be set proceed as
follows:

There are two ways to reduce the

hardness: one way is using water softener, the other is using

detergent.

water

Remove the lower basket and then unscrew and remove the cap from the salt

container.

If you are filling the container for the first time ,fill 2/3 of its volume with water

(around 500ml).

Place the end of the funnel(supplied) into the hole and introduce about 1.2kg of

salt .It is normal for a small amount of water to come out of the salt container

Carefully screw the cap back on.

1

2

4

3

Usually, the salt warning light will be off in 2-6 days after the salt container be

filled with salt.

5

dH

mmol/l

0~14

0~8

0~1.4

/

0

/

14~39

8~22

1.4~3.9

-

20

60

39~80

22~45

3.9~8

Mid

40

30

>80

>45

>8

+

60

20

fH

0~10

10~28

28~56

>56

Clark

WATER HARDNESS

Selector Position

Salt consumption

(gram/cycle)

Auto nomy

(cycles/1.2kgs)

°Clark: British degree

°fH : French degree

°dH : German degree

Note:1 °dH=1.25

°Clark=1.78

°fH=0.178mmol/l

°

°

°

°

°

°

Summary of Contents for EDW-1290















Reviews: