Elba EDW-1290 Instruction Manual Download Page 12

10

If the sink is 1000 higher from the floor, the excess water in hoses cannot
be drained directly into the sink. It will be necessary to drain excess

water from hoses into a bowl or suitable container that is held outside and lower

than the sink.

Connect the cold water supply hose to a threaded 3/4(inch) connector and make sure that it is

fastened tightly in place.

If the water pipes are new or have not been used for an extended period of time, let the water

run to make sure that the water is clear and free of impurities. If this precaution is not taken,

there is a risk that the water inlet can get blocked and damage the appliance.

The water supply to the appliance can also be connected to the house hot water line

(centralized system, heating system),as long as it does not exceed a temperature of 60 C.

In this case, the wash cycle time will be shortened by about 15 minutes and the wash
efficiency slightly reduced.

The connection must be made to the hot water line following the same procedures as those
for the connection to the cold water line.

DIMENSIONS(mm)

Insert the drain hose into a drain pipe with a minimum diameter of 40 mm, or let it run into the sink, making sure to avoid bending
or crimping it. Use the special plastic support that comes with the appliance. The free end of the hose must be at a height

between 400 and 1000mm and must not be immersed in water.

Once the appliance is positioned,adjust the feet (screwing them in or out) to adjust the
height of the dishwasher, making it level. In any case ,the appliance should not be inclined

more than 2 .

Position the appliance in the desired location. The back should rest against the wall behind it, and the sides, along the adjacent

cabinets or wall. The dishwasher is equipped with water supply and drain hoses that can be positioned to the right or the left to

facilitate proper installation.

600

580

850

1135

In order to avoid that there is more water

staying in the inlet hose,please close the hydrant

after using.(For the models: no safety inlet hose.)

φ 40mm

Summary of Contents for EDW-1290















Reviews: