background image

 
 

DESIGN LED 36 Pro™

 

©Elation Professional, Los Angeles Ca. 

17 

 

www.ElationLighting.com

   

setting the correct DMX address on the digital display located on the back of the fixture. 

 

You can set the same starting address for all fixtures or a group of fixtures, or set different 

address for each individual fixture. Be advised that setting all you fixtures to the same DMX 

address will subsequently control all fixtures in the same fashion, in other words, changing 

the settings of one channel will affect all the fixtures simultaneously. 

 

If  you  set  each  fixture  to  a  different  DMX  address,  each  unit  will  start  to  “listen”  to  the 

channel number you have set, based on the quantity of control channels (DMX channels) of 

each fixture. That means changing the settings of one channel will only affect the selected 

fixture. 

 

In the case of the Design LED 36 Pro™, which is up to a six channel fixture (default may also 

be set to three or four channels), you should set the starting DMX address of the first unit to 

1, the second unit to 7 (6 + 1), the third unit to 13 (6 + 7), and so on. 

 

Note: 

During  start-up  the  Design  LED  36  Pro™  will  automatically  detect  whether  a  DMX 

data signal is being received or not. If a DMX data signal is being received, the display will 

show 

"A.XXX" (XXX 

representing the actual DMX address). If the fixture is not receiving a 

DMX signal the display will flash 

"A.XXX" (XXX 

representing the actual DMX address).   

 

If your fixture is connected to a DMX controller and the display is flashing (not receiving a 

DMX signal), please check the following: 

-    The 3-pin XLR plug (cable with DMX signal from controller) may not be connected or 

is not inserted completely into the DMX input jack. 

-

  The DMX controller is switched off or defective. 

-

  The DMX cable or connector is defective. 

-

  A DMX terminator has been inserted into the last fixture in your DMX chain. 

 

 

 

Summary of Contents for 36 PRO

















































Reviews: