manualshive.com logo in svg

ekwb SLIM 120, User Manual

Share
Download
ekwb SLIM 120 User Manual Download Page 23

/ 21 /

STEP 5.: 

Slide the fitting ring towards the barb and tighten it in clockwise direction as 
far as it goes.

Repeat the procedure on all the fittings in order to connect the water cooling 
loop.

The liquid cooling loop components are now connected and the cooling cir-
cuit is now complete.

STEP5

CONNECTING THE PUMP-RESERVOIR 

UNIT

Take the cable with 4-pin PWM (fan) connector from the pump-reservoir unit.

Plug it to the male connector header located on the motherboard. Always 
use CPU-dedicated fan headers if possible.
 

Always use CPU fan header. On majority of motherboards these 
headers usually offer best PWM regulation.

In order to fill the liquid cooling loop for the first time as well as do a 
proper leak test you should connect the pump directly to the pow-
er supply independently (without turning on your PC hardware). 
Please proceed to Page 23, chapter RECOMMENDED FILLING 
AND LEAK-TESTING PROCEDURE.

ELECTRICAL CONNECTIONS

Summary of Contents for SLIM 120





































Reviews:

No comments

Brands by name

Popular brands

Load more brands