manualshive.com logo in svg

ektor 03135 EV-MERCURY, Installation Instructions Manual, Page: 14 / 20

Share
Download
ektor 03135 EV-MERCURY Installation Instructions Manual Download Page 14

MERCURY EMERGENCY INSTALLATION INSTRUCTIONS

14

18. SELF TEST INDICATOR LEDS

The table below shows the operation of the Mercury status indicators:

19. SELF TEST/ COMMISSIONING INTERVAL PROGRAMMING

The self test mode must first be enabled to perform tests by switching the breaker, or test button in the 
correct sequence. The test interval is fixed and set to 26 weeks / 182 days. The LEDs indicate the status of the 
device and which functions are being performed. For more information refer to the 

Configurations: Status 

LEDs and Device Modes 

document. 

When self test mode is enabled the status LED will flash either 4x (switched active detected)
or 3x (switched active not detected) for 2 minutes.

The self test can also be enabled using the test button sequence below:

INDICATOR

DESCRIPTION

YELLOW
2sec ON / 2sec OFF

YELLOW
4sec ON / 1sec OFF

YELLOW
0.5sec ON / 0.5sec OFF

GREEN
1xFlash

Device is performing a duration test

Last duration test passed. The duration was met when last run.
Test ran less than five days ago

Last duration test failed. Failed to meet duration. The device is not 
currently running a new test. Mains is on

A duration test is pending. The device is not in any self test and is
set to normal mode

  

3X PRESS & RELEASE

WAIT & REPEAT

WAIT 30 sec.

then repeat the

3X press & release

NOTE: 

If the wait in-between breaker or test button push sequences is longer than 

50 seconds 

         

then it will timeout  and the procedure will need to begin again.

30 sec.

RELEASE

PRESS

RELEASE

PRESS

RELEASE

PRESS

8 sec.

5X SWITCH CYCLES

WAIT & REPEAT

WAIT 30 sec.

then repeat the

5X SWITCH CYCLE

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

  

30 sec.

8 sec.

Summary of Contents for 03135 EV-MERCURY





















Reviews:

No comments