background image

 

EKOSync 1588A User Manual rev 1.1 

August 2021 

 
 

         Safety  

 

For  your  safety,  the  following  general  safety  precautions  must  be  observed  during  all 
phases of operation of this instrument. 

 

 

WARNING! THIS DEVICE MUST BE EARTHED 

                             

 

                               Do not use this equipment in a manner not specified by the manufacturer. The protective features 

of this product may be impaired. It could cause unavoidable damage to the equipment, personal 
injury and/or death. 
 
Reviewing the complete documentation before installing or operating the instrument is important. 

 

WARNING! HAZARDOUS VOLTAGES CAN CAUSE SHOCK, BURNS AND DEATH. 
 
The  power  plug  shall  be  disconnected  from  all  voltage  sources  before  it  is  opened  for  any 
adjustment, replacement, maintenance or repair. 
 
Any adjustment, maintenance and repair of the opened instrument under voltage shall be avoided 
and, if unavoidable, shall be carried out only by a qualified person who is aware of the general device 
test practices. 

 

All  recommended  equipments  that  should  be  earthed.  Any  interruption  of  the  mains  earth 
conductor inside or outside the instrument will make the instrument dangerous. 
 
Do not install substitute parts or perform any unauthorized modification to the product. 
 
Unless  otherwise  specified  in the  documentation, there are  no  user-serviceable parts  inside this 
instrument. 
 
Instruments  that appear  damaged or  defective  should  be  secured against  unintended  operation 
until they can be repaired by qualified service personnel. 
 
This instrument is intended for use in dry, indoor locations only. 
 

                Do not wet the instrument when cleaning it. 
 

Safety Symbols 
 

These symbols, which have these meanings, may be marked on this instrument.  

 

                  
 

EARTH (GROUND) TERMINAL 

 

 

 

Summary of Contents for EKOSync 1588A


























Reviews: