background image

2

2.Proper usage

Please use the electric pallet truck accord to this specification.

This is a walkie type electric pallet truck with autonomous control, lifting and lowering

is controlled by the handle button. Improper use can cause personal injury or machine
damage. Operators or operating companies need to ensure proper using,

The Truck needs to be used on a firm, flat ,intact surface and suitable surface ,The truck

is designed for indoor use at room temperature from-10°C to +40°C

Use under light load without permanent barriers or pits, It is forbidden to operate on

the slopes. During Operation ,The goods must be placed approximately at the center of the
truck’s load center

Lifting or Carrying people is strictly prohibited.

It is prohibited to use this truck on lifting or loading ramps

The rated capacity is marked on the capacity label or nameplate. And the operator must pay
attention to the warming signs and safety instructions

Operating lighting must be at least 50LUX.

Modification

Any modification that may affect the truck rated capacity, stability, or safety operations must
be approved in advance by the Truck’s original manufacturer or Its authorized Manufacturer
or its successor. This includes the effects of changes such as Braking, steering ,Visibility, and
the addition of removable accessories.

After the manufacturer or its successor approves the modification or change, The capacity
name plate, Label, identification marks, operation and maintenance manual must be changed
accordingly

3.Introduction of the product

Summary of Contents for EP20D Series




























Reviews: