EKIZNSN F073 Owner'S Manual Download Page 2

Please read all safety instructions prior to installing your 

ceiling fan and save this document for future reference. 

If you are in doubt with any of the information provided 

or difficulty installing your fan, please the email customer 

service at:

 [email protected]

 

Before you begin installing the fan, shut power off the 

circuit breaker for the fuse box.

 

Read all instructions and safety information before 

installing your new fan.

 

All wiring must be in accordance with national and local 

electrical codes. ANSI/NFPA 70. If you are unfamiliar with 

wiring, use a qualified electrician.

 

Do not bend the blades while installing, balancing the 

blades, or cleaning the fan.

 

Do not insert foreign objects in between rotating fan 

blades.

 

Make sure the installation site you choose allows the fan 

blades to rotate without any obstructions.

 

To Reduce the Risk of Electric Shock, Disconnect the 

electrical supply circuit before installing the light kit.

 

After you install the fan, make sure that all mounting 

components are secured to prevent the fan from falling.

 

Turn the fan off and wait for the blades to stop 

completely before performing any maintenance or 

cleaning.

Safety Rules

Summary of Contents for F073













Reviews: