eisenblatter GLADIUS 1802 HT, Original Instructions Manual

Page: 22 / 24

www.eisenblaetter.de
22
Original instructions GLADIUS
®
1802 HT
EN
d) Put the machine upright again (figure E4) and
apply light pressure until the locking pin unlocks
automatically.
Figure E5 shows the machine with the sanding belt
correctly tensioned.
Before using the machine, make sure that the
sanding belt is correctly seated (see page 4,
figures F1 and F2). The sanding belt must lie cleanly on
the machine parallel to the belt guide bar. If necessary,
the sanding belt must be readjusted!
10.2 Adjusting the sanding belt
If the sanding belt does not lie cleanly on the machine
(see page 4, figure F1), the sanding belt must be
readjusted – see page 5, figures H1 to H6.
You need the following tools to adjust the sanding belt:
• 5 mm Allen key (art. no. 53341 – included)
• 3 mm Allen key (art. no. 53342 – included)
• Wrench for clamping nut M14 (art. no. 65009a
– included)
a) Switch on the machine and set the speed adjusting
wheel to level 2 (figure H1).
b) Adjusting the sanding belt on the drive roller:
Open the locking screw (3) (figure H2).
Turn the adjusting screw (4) in the direction of the
arrow until the sanding belt is in the correct position
(figure H3).
Then tighten the locking screw (3) and the screw (A)
(figure H3).
c) Adjusting the sanding belt on the pulley:
Open the locking screw (2) (figure H4).
Turn the adjusting screw (1) in the direction of the
arrow until the sanding belt is in the correct position
(figure H5).
Then tighten the locking screw (2) again (figure H6).
If necessary, repeat steps b) and c) until the correct
position of the sanding belt is achieved parallel to the
belt guide bar (see page 4, figure F2).
During operation, make sure that the sanding belt
is always in the optimal position.
10.3 Settings for plane and convex grinding
With the help of the adjusting screws (A3-3), the
GLADIUS
®
1802 HT can be adjusted for convex or flat
grinding as required – see page 5, figures K1 and K2.
Flat grinding – figure K1:
With the help of the adjusting screw (A3-3), the guide
rails are aligned horizontally in order to be able to create
a uniform finish with a flat finish.
Convex grinding (for precise grinding work) – figure K2:
The guide bars are pressed down using the adjusting
screws (A3-3) to enable convex grinding, e.g. B. for
welding point machining.
11. Switching on and off
Always guide the machine with both hands.
Always hold one hand on the handle (A1-4) when
working with the machine.
Switch on first, then guide the accessory towards
the workpiece.
Avoid inadvertent starts: always switch the tool off
when the plug is removed from the mains socket
or if there has been a power cut.
The machine must not be allowed to draw in
additional dust and shavings. When switching the
machine on and off, keep it away from dust deposits.
After switching off the machine, only place it down when
the motor has come to a standstill.
In continuous operation, the machine continues
running if it is forced out of your hands. Therefore,
always hold the machine with both hands using the
handles provided, stand securely and concentrate.
Torque activation (with dead man‘s lever):
Switching on:
See page 3, figure B1.
Slide the trigger switch (A1-10) forwards and then push
it upwards.
Switching off: Release the trigger switch (A1-10).
Continuous operation:
Switching on:
See page 3, figure B2.
Switch the machine on as described above. Now slide
the trigger switch (A1-10) forwards again and release in
the front position to lock the trigger switch (continuous
operation).
Switching off: Push the trigger switch (A1-10) upwards
and release.