EIP Limited AF5100, Owner'S Manual

Page: 4 / 8

AF5100 OWNERS MANUAL
4
4. Operation
•
Select suitable location for dryer.
•
IMPORTANT – Ensure dryer is in a safe position. Do
not sit dryer in a puddle and make sure it is protected
from drips and splashes.
•
Fully unwind the supply cord from the cable winder and
plug into a convenient socket outlet
•
Place the dryer in a desired operating position. (see fig
1-5 page2)
1. Tilt Back – Tilt the Axial Fan backward on the four
curved molded legs at an angle to direct air for
elevated drying.
2. Upright – Set the axial Fan square with the handle
on the top to direct air across the room.
3. Tilt Forward – Tilt the Axial Fan forward on the
“standing legs at an angle to direct airflow along the
flow in front of the dryer.
4. Face Down – Set the Axial Fan on the four curved
molded legs with the “standing legs” facing up to
direct air straight down.
5. Power Pitch – place on 3º down angle leg.
6. Stack for Storage – Axial fans interlock and stack for
easy storage and transport.
•
Set the desired speed low or high.
•
Check for proper operation before leaving the unit
unattended. Do not move or carry the dryer when it is
running.
•
To stop the machine turn switch to OFF (position ‘O’).
5. Storage
Always unplug and wipe down and dry the machine after
use. Wrap supply cord around the cable winder ensuring
that the plug is not trailing on the floor.
Store the machine in a dry indoor area only.
6. Maintenance
WARNING – Before undertaking maintenance
operation or adjustments switch off machine and
unplug from electricity supply.
The machine requires minimum maintenance apart from
the following checks by the operator.
•
Supply cord – Regularly inspect sheath, plug and cord
anchorage for damage or loose connection.
•
Body of the machine – Clean with a damp cloth.
•
Air vents – Check for dust accumulation around the air
inlet and outlet vents and clean if necessary. Blocked
vents will cause the motor to overheat, and may lead to
premature failure. Warranty claims for this type of
damage will not be accepted.
•
Motor overload cut-out – All machines are witted with
an automatic reset motor overload cut-out. The cut-out
will operate to protect the motor from overheating by
switching the machine off. Should the cut-out operate it
will reset automatically when the motor has cooled
sufficiently, usually after 15 – 30 minutes.
IMPORTANT – Should the machine fail to operate
contact EIP Customer Service Department for rapid
attention.
7. After sales service
EIP machines are high quality machines that have been
tested for safety by authorized technicians. It is always
apparent that after longer working periods, electrical and
mechanical components will show signs of wear and tear
or ageing.
To maintain operational safety and reliability the following
service interval has been defined. Every year or after 250
hours.
Under extreme or specialized conditions and/or
insufficient maintenance intervals are necessary. Use
only original EIP spare parts. Use of other spare parts will
invalidate all warranty and liability claims!
Should you require after sales service please contact the
supplier from whom you purchased the machine, who will
arrange service. Repairs and servicing of EIP products
should only be performed by trained staff. Improper
repairs can cause considerable dangers to the user.
8. Guarantee
Your product is guaranteed for one year from the date of
original purchase, or hire purchase, against defects in
materials or workmanship during manufacture. Within the
guarantee period we undertake at our discretion, to repair
or replace free of charge to the purchaser, any part found
to be defective, subject to the following conditions.
CONDITIONS
1 Claims made under the terms of the guarantee must
be supported by the original invoice/bill of sales
issued at the time of sale, or the machine Serial No.
2 For claims under this guarantee contact the supplier
from whom you purchased the product who will
arrange the appropriate action. Do not initially return
the product as this could result in transit damage.
3 Neither EIP nor its distributor shall be liable for any
incidental or consequential loss.
4 This guarantee is governed by the laws of England.
5 This guarantee does not cover any of the following:
ƒ Periodic maintenance, and repair or replacement
of parts due to normal wear and tear.
ƒ Damage caused by accident, misuse or neglect,
or the fitting of other than genuine EIP parts.
ƒ Defects in other than genuine EIP parts, or
repairs, modifications or adjustments performed
by other than a EIP service engineer or
authorized service agent.
ƒ Costs and risks of transport relating directly or
indirectly to the guarantee of this product.
ƒ This guarantee does not affect your statuary
rights, or your rights against the supplier arising
from their sales or purchase contract.
EIP Limited’s policy is one of continual product
development and we reserve the right to alter
specifications without prior notice.