GB
- 21 -
5.5 Suction nozzles
Combination nozzle (Fig. 3)
The dual-purpose nozzle (14) is for vacuuming
solids and liquids over medium to large areas.
Crevice nozzle (Fig. 3)
The crevice nozzle (23) is designed for vacu-
uming solids and liquids in corners, edges and
other areas that are di
ffi
cult to access.
Upholstery nozzle (Fig. 3)
The upholstery nozzle (26) is specially designed
for vacuuming solids on upholstery and carpets.
6. Operation
6.1 ON/OFF switch (Fig. 1/7)
Switch position 0:
O
ff
Switch position I:
Normal mode
Switch position AUTO:
Automatic mode
6.2 Dry vacuuming
Use the pleated
fi
lter (24) for dry vacuuming (see
point 5.2). The dirt bag (27) can be
fi
tted in additi-
on when removing particularly stubborn dirt (see
point 5.3).
If you want to suction large amounts of
fi
ne dust,
you can use the coarse
fi
lter (16) (see point 5.2
Fitting the coarse
fi
lter).
Always ensure that the
fi
lters are securely seated.
6.3 Wet vacuuming
For wet-vacuuming, use the foam
fi
lter (25) (see
point 5.2).
For wet suctioning,
fi
t the sealing ring (37) (see
point 5.2 Fitting the sealing ring).
Check that the
fi
lter is securely seated at all times.
Water drain screw (Fig.1)
To make the tank (10) easier to empty after wet
vacuuming, it is
fi
tted with a water drain screw
(11). Open the water drain screw (11) by turning it
anti-clockwise and drain the liquid.
When wet vacuuming, the
fl
oating safety switch
(Fig. 2/21) closes when the maximum tank level
is reached. At the same time, the suction noise of
the equipment will change and become louder.
You must then switch o
ff
the equipment and em-
pty the tank.
Danger!
The wet and dry vacuum cleaner is not suitable
for the vacuuming of combustible liquids.
For wet vacuuming, use only the supplied foam
fi
lter.
6.4 Automatic mode (Fig. 1)
Connect the power cable on your electric tool to
the automatic socket-outlet (4) and connect the
suction hose (9) to the extractor connector on
your electric tool. Check that the connections are
secure and air-tight.
You can use the supplied electric tool adapter
(Fig. 3/22) to connect the suction hose (9) to the
electric tool. To do so,
fi
t it between the suction
hose and the extractor port on the electric tool.
Set the switch (7) on the wet and dry vacuum
cleaner to position AUTO (automatic mode). The
moment you switch on the electric tool, the wet
and dry vacuum cleaner switches on as well.
When you switch o
ff
the electric tool, the wet and
dry vacuum cleaner switches o
ff
as well after a
pre-set delay.
6.5 Blowing
Connect the suction hose (Fig. 1/9) to the blow
connector (Fig. 2/19) on the wet and dry vacuum
cleaner.
6.6 Filter cleaning system (Fig. 20a-20b)
The equipment has a
fi
lter cleaning system which
enables large amounts of
fi
ne dust to be suc-
tioned without
fi
tting the dirt collector bag.
Important!
The
fi
lter cleaning system is only allo-
wed to be activated if the coarse
fi
lter is
fi
tted!
Important!
The
fi
lter cleaning system can only be
activated if the equipment is in operation!
If there is a drop in suction performance, the
fi
lter
cleaning system can be activated at the touch of a
button in order to clean the dirty coarse
fi
lter and
increase the suction performance again.
Actuate the cleaning button (1) six times while
the equipment is in operation with the end of the
suction hose. Keep the button pressed down for
4 seconds each time you actuate it. Ensure that
the suction hose does not become kinked when
you do so.
Anl_TE_VC_2230_SAC_SPK9.indb 21
Anl_TE_VC_2230_SAC_SPK9.indb 21
14.11.2018 13:54:23
14.11.2018 13:54:23
