EINHELL TE-SW 18/610 Li-Solo, Original Operating Instructions

Page: 20 / 130

GB
- 20 -
5. Before starting the equipment
5.1 Fitting the feed-in brushes (Fig. 3-5)
Fit the feed-in brushes (4,5) as shown in Figs. 3-5.
Make sure that you fi t them in accordance with
the markings on the brushes and brush mounts.
5.2 Fitting the push bar (Fig. 6-9)
Fit the top push bar and bottom push bar (2, 3)
as shown in Figs. 6-8. Make sure that the pins are
properly latched in position on both sides (Fig. 6,
Item A) during assembly. The height of the push
bar can be adjusted a little by selecting the fas-
tening hole (Fig. 7, Item C, B) accordingly. Then
fasten the power cable to the push bar (Fig. 9)
with the cable clips (10).
5.3 Charging the battery (Fig. 10)
1. Take the battery pack out of the equipment.
Do this by pressing the side pushlock buttons.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(d) into the socket outlet. The green LED will
then begin to fl ash.
3. Slot the battery pack (16) onto the battery
charger (d).
4. In the section entitled „Charger indicator“ you
will fi nd a table with an explanation of the LED
indicator on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
•
the charger
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
Fitting the battery (Fig. 11)
Open the battery cover (15). To do so, fl ip the co-
ver up as shown in Fig. 13. Then slot the rechar-
geable battery (16) into the mount and push them
forward until you hear the battery engage.
Battery capacity indicator (Fig. 12)
Press the battery capacity indicator switch (a).
The battery capacity indicator (b) will indicate the
charge status of the battery by means of 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED blinks:
The battery is empty, recharge the battery.
All LEDs blink:
The battery pack has undergone exhaustive di-
scharge and is defective. Do not use or charge a
defective battery pack.
6. Operation
6.1 Switching bar (Fig. 1)
Switching on:
Press the switching bar (1).
Switching o ff :
Release the switching bar (1).
Important! Only activate the push sweeper when
it is stood on the fl oor/ground; otherwise the feed-
brushes may be damaged.
6.2 Lip (Fig. 13)
For better sweeping results, the lip should be
fi tted.
The lip (17) can be removed for sweeping very
uneven surfaces to avoid tilting. To do so, undo
the two screws (A) as shown in Fig. 13 and then
remove the lip.
Anl_TE_SW_18_610_SPK9.indb 20 Anl_TE_SW_18_610_SPK9.indb 20 07.04.2020 11:07:07 07.04.2020 11:07:07