GB
- 22 -
4. Technical data
Motor power supply: ............................... 18 V DC
Idling speed: ........................................4200 min
-1
Cutting depth at 90°: ................................ 48 mm
Cutting depth at 45°: ................................ 32 mm
Saw blade: ..........................................Ø 150 mm
Blade holder: ....................................Ø 10/16 mm
Blade thickness: ...................................... 1.6 mm
Weight: .......................................................2.8 kg
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 60745.
L
pA
sound pressure level ................... 83,83 dB(A)
K
pA
uncertainty .............................................3 dB
L
WA
sound power level ..................... 94,83 dB(A)
K
WA
uncertainty .............................................3 dB
Wear ear-mu
ff
s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 60745.
Handle
Vibration emission value a
h, W
= 3.534 m/s
2
K uncertainty = 1.5 m/s
2
Additional handle
Vibration emission value a
h, W
= 3,889 m/s
2
K uncertainty = 1.5 m/s
2
The speci
fi
ed vibration value was established in
accordance with a standardized testing method.
It may change according to how the electric
equipment is used and may exceed the speci
fi
ed
value in exceptional circumstances.
The speci
fi
ed vibration value can be used to
compare the equipment with other electric power
tools.
The speci
fi
ed vibration value can be used for initi-
al assessment of a harmful e
ff
ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment’s construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
5. Before starting the equipment
Warning!
Always remove the battery pack before making
adjustments to the equipment.
5.1 Setting the cutting depth (Figure 2/3)
•
Release the handle on the rear of the guard
hood for adjusting the cutting depth (4).
•
Place the saw foot (6) flat on the surface of
the workpiece you wish to saw. Raise the saw
until the saw blade (12) is at the required cut-
ting depth (a).
•
Refasten the handle for adjusting the cutting
depth (4). Check the handle is securely faste-
ned.
5.2 Miter stop (Figure 4/5)
•
The preset standard angle between the saw
foot (6) and saw blade (12) is 90°. You can
adjust this angle to carry out angled cuts.
•
Release the locking lever for miter setting (7)
on the front of the saw foot.
•
You can now adjust the cutting angle to
around 45°. Keep an eye on the cutting angle
Anl_TE_CS_18_Li_solo_SPK9.indb 22
Anl_TE_CS_18_Li_solo_SPK9.indb 22
21.05.2019 14:51:49
21.05.2019 14:51:49
