GB
- 42 -
5. Before starting the equipment
Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Always pull the power plug before making
adjustments to the equipment.
5.1 General information
•
The equipment must be set up where it can
stand securely, i.e. it should be bolted to a
workbench, a universal base frame or similar.
•
All covers and safety devices have to be pro-
perly fitted before the equipment is switched
on.
•
It must be possible for the blade to run freely.
•
When working with wood that has been pro-
cessed before, watch out for foreign bodies
such as nails or screws, etc.
•
Before you actuate the On/Off switch, make
sure that the saw blade is correctly fitted
and that the equipment’s moving parts run
smoothly.
5.2 Assembling the saw (Fig. 1-5)
•
To adjust the turntable (17), loosen the lo-
cking screw (14) by approx. 2 turns, which
frees the turntable (17).
•
Turn the turntable (17) and scale pointer (15)
to the desired angular setting on the dial (16)
and lock into place with the locking screw
(14). The saw has locking positions at angles
of - 45°, -31.6°, -22.5°, -15°, 0°, 15°, 22.5°,
31.6° and 45°, at which the turntable (17) au-
dibly clicks into position.
•
To release the saw from its position at the
bottom, pull the fastening bolt (25) out of the
motor mounting while pressing down lightly
on the machine head (4). Turn the fastening
bolt (25) through 90° before releasing it, so
that the saw remains unlocked.
•
Swing the machine head (4) up until the re-
lease lever (3) latches into place.
•
The clamping device (8) can be fitted on the
left or right of the fixed saw table (18).
•
Undo the locking screws for the workpiece
support (26).
•
Mount the workpiece support (10) on the
fixed saw table (18) and tighten the appropri-
ate locking screw (26) (Figure 4, 5).
•
Mount the second workpiece support (10) on
the opposite side of the saw and secure with
the appropriate locking screw (26).
•
When the locking screw (21) is loosened, you
can tilt the machine head (4) to the left by up
to 45°.
•
To ensure that the saw is standing securely,
adjust the adjustable foot (13) by turning it so
that the saw stands in a horizontal and firm
position.
5.3 Precision adjustment of the stop for cros-
scut 90° (Fig. 6-8)
•
Fasten the turntable (17) in 0° position.
•
Undo the locking screw (21) and move the
machine head (4) all the way to the right using
the handle (1).
•
Place the 90° angular stop (a) between the
blade (7) and the turntable (17).
•
Adjust the adjustment screw (29) until the
angle between the blade (7) and the turntable
(17) equals 90°.
•
Finally check the position of the pointer (20)
on the scale (19). If necessary, undo the poin-
ter (20) with a Philips screwdriver, set it to the
0° position on the scale (19) and retighten the
retainer screw.
•
No stop angle included.
5.4 Precision adjustment of the stop for miter
cut 45° (Fig. 1, 7, 9)
•
Fasten the turntable (17) in 0° position.
•
Undo the locking screw (21) and move the
machine head (4) all the way to the left using
the handle (1), until it coincides at 45°.
•
Place the 45° stop angle (b) between the bla-
de (7) and the turntable (17).
•
Adjust the adjustment screw (30) so that the
angle between the blade (7) and the turntable
(17) equals exactly 45°.
•
No stop angle included.
5.5 Adjusting the miter angle on the machine
head (Fig. 2, 12-13)
•
Undo the locking screw (21).
•
Hold the machine head (4) by the handle (1).
•
After pulling the button (33), the machine
head can be tipped infinitely as well as to se-
veral locking points.
•
Angles to the left: 0-45°
•
Angles to the right: 0-45°
•
Re-tighten the locking screw (21).
5.6 Adjusting the removable stop rail
(Fig. 1, 10-14)
•
Important! This saw is equipped with a re-
movable stop rail (9) which is screwed to the
fixed stop rail (11).
•
For miter cuts and double miter cuts with the
Anl_TC_SM_2534_Dual_SPK8.indb 42
Anl_TC_SM_2534_Dual_SPK8.indb 42
15.03.16 12:07
15.03.16 12:07