GB
- 18 -
4. Technical data
Motor power supply: ............................... 18 V DC
Idling speed: ...........................11000-20000 min
-1
Sanding/grinding area: ............. 90 x 90 x 90 mm
Oscillation angle: ...........................................3.2°
Weight: .....................................................0.86 kg
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 60745.
L
pA
sound pressure level ........................ 78 dB(A)
K
pA
uncertainty .............................................3 dB
L
WA
sound power level .......................... 89 dB(A)
K
WA
uncertainty .............................................3 dB
Wear ear-mu
ff
s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 60745.
Handle
Vibration emission value a
h
= 13.9 m/s
2
K uncertainty = 1.5 m/s
2
The speci
fi
ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the speci
fi
ed value
in exceptional circumstances.
The speci
fi
ed vibration value can be used to
compare the equipment with other electric power
tools.
The speci
fi
ed vibration value can be used for initi-
al assessment of a harmful e
ff
ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment’s construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
5. Before using the equipment
Warning!
Always remove the battery pack before making
adjustments to the equipment.
Be sure to read the following information before
you put the cordless equipment into operation:
•
Charge the battery pack with the charger.
5.1 Fitting the plug-in tools (Fig. 1/2)
•
To fit the plug-in tools safely you should
hold the multifunction tool so that the On/Off
switch (1) points down and the tool chuck (2)
faces up.
•
Place the plug-in tool (e.g. the triangular
grinding/sanding plate or HCS saw blade) on
the tool mounting (2) so that the pins of the
tool mounting (2) fit into the recesses in the
plug-in tool.
•
Secure the plug-in tool using the supplied
socket head screw (14) and tighten the screw
securely with the hexagon key (5).
•
Make sure that the washer (13) is used for the
socket head screw (14) (see Fig. 2).
Check that the plug-in tool is secure!
5.2 Triangular sanding/grinding plate
Fit the triangular sanding/grinding plate to use the
equipment as a delta sander/grinder.
5.2.1 Fastening the sanding/grinding paper
The Velcro fastener enables easy changing of
the abrasive paper. Make sure that the vacuum
extraction holes on the abrasive paper and the
grinding/sanding disk are aligned.
Anl_TC_MG_18_Li_SPK9.indb 18
Anl_TC_MG_18_Li_SPK9.indb 18
08.08.2018 11:13:42
08.08.2018 11:13:42