GB
- 21 -
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts of the charging unit
If the battery still fails to charge, send
•
the charging unit
•
and the screwdriver
to our customer service center.
Timely recharging of the battery will help it serve
you well for a long time. You must recharge the
battery when you notice that the power of the
cordless screwdriver drops.
6.2 Changeover switch (Fig. 3/Item 10)
The slide switch above the On/O
ff
switch is for
setting the direction of rotation of the cordless
screwdriver and for preventing the cordless
screwdriver from being switched on inadvertently.
You can select between clockwise and counter-
clockwise rotation. Change the direction of rota-
tion only when the equipment is at a standstill.
If you fail to observe this point, the gearing may
become damaged. When the slide switch is in the
middle position, the On/O
ff
switch is blocked.
6.3 On/O
ff
switch (Fig. 3 / Item 9)
Press the On/O
ff
switch to switch the cordless
screwdriver on. Release the On/O
ff
switch again
to switch it o
ff
.
6.4 LED lamp (Fig. 3/Item 2)
The LED lamp (2) can be used to additionally illu-
minate the area where you want to drill or screw.
The LED lamp (2) will be lit automatically as soon
as you press the On/O
ff
switch (9).
6.5 Angle setting (Fig. 3+4/Item 7)
The screwdriver can be locked into 2 di
ff
erent
angle settings. To do so, press and hold the lo-
cking button (7) and move the screwdriver into the
desired position. Then release the locking button
(7) again.
Important. Before you switch on the screwdriver,
make sure that it is correctly locked in the angle
position in question.
6.6 Battery capacity indicator (Fig. 5/Item 5)
Remove the cordless screwdriver from the char-
ging unit/charging station.
Press the button for the battery capacity indicator
(6). The battery capacity indicator (5) indicates
the charge state of the battery on 3 colored LEDs.
All the LEDs are lit:
The battery is fully charged.
The yellow and red LEDs are lit:
The battery has an adequate remaining charge.
Red LED:
The battery is empty, recharge the battery.
6.7 Torque setting (Fig. 5 / Item 3)
The torque for a particular screw size is set with
the setting ring (3). The torque is dependent on a
number of factors:
•
On the type and hardness of the material
involved
•
On the type and length of the screws used
•
On the requirements that the screw connec-
tion has to satisfy
The grating disengagement of the coupling in-
dicates that the selected torque level has been
reached.
Important. Only ever adjust the setting ring
when the equipment is at a standstill.
6.8 Magnetic screw holder (Fig. 5/Item 4)
Screws can be placed on the magnetic screw hol-
der for easy reach during operation.
6.9 Changing the bit (Fig. 6)
Important. Set the changeover switch to its center
position whenever you carry out any work (for
example changing the bit, maintenance , etc.) on
the cordless screwdriver.
•
Pull back and hold the locking sleeve (13).
•
Insert the bit (a) in the bit chuck (1) and let go
of the locking sleeve (13).
•
Check that the bit is locked in placed by
pulling on it.
6.10 Screws
It is advisable to use self-centering screws (e.g.
Torx, cross recessed head) as these will enable
you to work safely and reliably. Always make sure
that the bit used is of the same size and shape as
the screw.
Anl_SA_RT_SD_3_6_Li.indb 21
Anl_SA_RT_SD_3_6_Li.indb 21
15.01.13 15:34
15.01.13 15:34
Summary of Contents for RT-SD 3,6/1 Li
Page 29: ... 29 Anl_SA_RT_SD_3_6_Li indb 29 Anl_SA_RT_SD_3_6_Li indb 29 15 01 13 15 34 15 01 13 15 34 ...
Page 30: ... 30 Anl_SA_RT_SD_3_6_Li indb 30 Anl_SA_RT_SD_3_6_Li indb 30 15 01 13 15 34 15 01 13 15 34 ...
Page 31: ... 31 Anl_SA_RT_SD_3_6_Li indb 31 Anl_SA_RT_SD_3_6_Li indb 31 15 01 13 15 34 15 01 13 15 34 ...
