1. Safety information
Please read the instructions for use very carefully
and observe the information they contain. By
referring to these instructions, familiarize yourself
with the appliance, learn how to use it correctly,
and note the safety precautions to be taken.
Take the appropriate steps to ensure that children
have no access to the appliance.
The user of the appliance is responsible for any
third parties in the work area.
Before using the appliance for the first time, an
electrician must check that the necessary
electrical protection measures have been taken.
In stagnant water bodies, garden ponds,
swimming ponds and their surrounding areas the
pump may only be used with an earth-leakage
circuit breaker with an actuating rated current of
up to 30 mA (acc. to VDE 0100 part 702 and 738).
The pump is not designed for use in swimming
pools and paddling pools of any kind or other
bodies of water in which people or animals may
be present during operation.
It is prohibited to operate the pump if a person or
animal is in the danger area.
Ask your electrician!
Inspect the appliance before each use. Do not
use the appliance if the safety devices are
damaged or worn. Never deactivate the safety
devices.
Use the appliance only for the purposes specified
in these instructions for use.
You are responsible for safety in the work area.
Should the pump cable or plug be damaged by
external influences, the cable must not be
repaired! The cable must be replaced with a new
one. This work is to be performed only by an
electrician. (See section „Replacing the mains
cable“.)
Your mains supply must comply with the voltage
of 230 V alternating voltage specified on the type
plate.
Never lift, transport or secure the pump by its
power cable.
Make sure the appliance is plugged into a socket
in a place where there is no risk of flooding and
which is protected against moisture.
Always remove the plug from the socket before
doing any work on the pump.
Avoid exposing the pump to a direct jet of water.
The operator is responsible for any local safety
and installation regulations. (Ask your electrician
for advice.)
Rule out any indirect damage caused by the
flooding of rooms following the failure of the pump
by adopting the appropriate measures (e.g. the
installation of an alarm system, a reserve pump or
the like).
If the pump fails, any repair work necessary must
be performed only by an electrician or the ISC
Customer Service.
Never let the pump run dry and never operate it
with fully closed intake power. The manufacturer’s
warranty shall lapse if the pump is damaged due
to it being allowed to run dry.
The pump must not be used to operate swimming
pools.
The pump must not be installed in the drinking
water pipe line.
2. Durability
The maximum temperature of the medium to be
pumped in continuous operation should not exceed
+35°C.
This pump is not to be used to pump combustible,
gaseous or explosive fluids.
The pumping of aggressive fluids (acids, alkalis, silo
seepage etc.) and abrasive substances (sand)
should also be avoided.
3. Applications
Areas of use:
For irrigating and watering parks, vegetable
patches and gardens
For operating lawn sprinklers
With a prefilter, for drawing water from ponds,
streams, rain-butts, rain-water cisterns and wells.
Media which can be pumped:
For the pumping of clear water (fresh water), rain
water or mild suds/dirty water.
6
GB
Anl GPK 1500 Niro SPK1 28.09.2005 13:43 Uhr Seite 6
Summary of Contents for ROYAL GPK 1500 Niro
Page 34: ...34 1 30 VD 0100 702 738 230 ISC 2 35 RUS Anl GPK 1500 Niro SPK1 28 09 2005 13 43 Uhr Seite 34...
Page 36: ...36 8 3 4 1 IG C 1 2 9 0 5 5 10 11 RUS Anl GPK 1500 Niro SPK1 28 09 2005 13 43 Uhr Seite 36...
Page 37: ...37 RUS 12 13 www isc gmbh info ISC Anl GPK 1500 Niro SPK1 28 09 2005 13 43 Uhr Seite 37...
