GB
- 15 -
Tightening:
•
Caution! Only use the impact driver for loo-
sening screws/nuts. If you wish to use the
impact driver to tighten screws and nuts,
you must also use a torque limiter which is
designed for this purpose. If not, the screw
connection may be damaged. A torque limiter
is available from your dealer. It is not supplied
with this tool.
•
Prior to tightening, carefully insert the screw/
nut into the threads.
•
It is important that screws/nuts with special
torque specifications (for example provided
by the vehicle manufacturer in the automoti-
ve sector) are tightened only with a suitable
torque limiter.
Hazard!
Always tighten and check screws/nuts with a
torque wrench set to the torque speci
fi
ed by the
manufacturer.
7. Replacing the power cable
Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
8.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
8.2 Carbon brushes
In case of excessive sparking, have the carbon
brushes checked only by a quali
fi
ed electrician.
Danger!
The carbon brushes should not be rep
laced by anyone but a quali
fi
ed electrician.
8.3 Maintenance
There are no parts inside the equipment which
require additional maintenance.
8.4 Ordering spare parts and accessories
Please provide the following information when
ordering spare parts:
•
Type of unit
•
Article number of the unit
•
ID number of the unit
•
Spare part number of the required spare part
For our latest prices and information please go to
www.isc-gmbh.info
Tip! For good results we
recommend high-quality ac-
cessories from
!
www.kwb.eu
9. Disposal and recycling
The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council o
ffi
ces.
10. Storage
Store the equipment and accessories in a dark
and dry place at above freezing temperature. The
ideal storage temperature is between 5 and 30
°C. Store the electric tool in its original packaging.
Anl_CC_IW_950_SPK7.indb 15
Anl_CC_IW_950_SPK7.indb 15
26.08.15 08:23
26.08.15 08:23
Summary of Contents for CC-IW 950
Page 96: ...GR 96 Anl_CC_IW_950_SPK7 indb 96 Anl_CC_IW_950_SPK7 indb 96 26 08 15 08 23 26 08 15 08 23...
Page 105: ...105 Anl_CC_IW_950_SPK7 indb 105 Anl_CC_IW_950_SPK7 indb 105 26 08 15 08 23 26 08 15 08 23...
Page 106: ...106 Anl_CC_IW_950_SPK7 indb 106 Anl_CC_IW_950_SPK7 indb 106 26 08 15 08 23 26 08 15 08 23...
Page 107: ...107 Anl_CC_IW_950_SPK7 indb 107 Anl_CC_IW_950_SPK7 indb 107 26 08 15 08 23 26 08 15 08 23...
