GB
- 20 -
4. Technical data
Rated voltage: ................................230 V ~ 50Hz
Power input: ......................................... 235 watts
Idle speed: ..........................................3000 min
-1
Adjustment angle: ............40° to the left and right
Grinding wheel Ø (inside): ........................ 22 mm
Grinding wheel Ø (outside): ........... max. 145 mm
Grinding wheel thickness: ....................... 3.2 mm
Protection class: ................................................. I
Weight: .......................................................5.8 kg
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 61029.
L
pA
sound pressure level ..................... 68.3 dB(A)
K
pA
uncertainty .............................................3 dB
L
WA
sound power level ....................... 81.3 dB(A)
K
WA
uncertainty .............................................3 dB
Wear ear-mu
ff
s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 61029.
Grinding
Vibration emission value a
h
= 3.675 m/s
2
K uncertainty = 1.5 m/s
2
The speci
fi
ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the speci
fi
ed value
in exceptional circumstances.
The speci
fi
ed vibration value can be used to
compare the equipment with other electric power
tools.
The speci
fi
ed vibration value can be used for initi-
al assessment of a harmful e
ff
ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment’s construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
5. Before starting the equipment
The entire assembly process may only be carried
out after the power plug has been pulled.
Fitting the grinding head (Fig. 3a/3b)
The equipment consists of the grinding head (10)
and the base frame (11) which must still be
fi
tted.
Insert the centering pin of the grinding head into
the opening of the base frame. Now insert the
hexagon head bolt (A) from the front through the
hole in the grinding head and the oval hole in the
base frame and secure on the back with a washer
(B) and a star screw (C).
Fitting the handle (Fig. 4)
Screw the handle (13) into the intended hole on
the grinding head (10).
Mounting on a table or wall (Fig. 5/6)
The equipment is designed for both table top ins-
tallation and wall mounting.
When installing the equipment on a table top,
fi
rst
make sure that the edge of the equipment is
fl
ush
with the edge of the table, then secure the equip-
ment with the holes (A).
When mounting the equipment on the wall, use
the holes (C) to secure the equipment. Spacer
sleeves or the like should be used so that the roof
cutting angle set screw remains accessible.
When mounting the equipment on a wall, make
sure that it is not
fi
tted too high so as to avoid wor-
king at eye level.
Anl_GC_CS_235_E_SPK7.indb 20
Anl_GC_CS_235_E_SPK7.indb 20
25.11.2020 15:19:28
25.11.2020 15:19:28
