EN
- 15 -
contact with the workpiece.
•
Hold the circular saw firmly with both hands.
6.3 Switching On/O
ff
(Fig. 11)
Switching on:
Press the locking button (3) and the On/O
ff
switch
(2) at the same time.
•
Allow the saw blade to accelerate until it
reaches full speed. Then slowly move the saw
blade along the cutting line. Exert only gentle
pressure on the saw blade as you do so.
Switching o
ff
:
Release the locking button and On/O
ff
switch
•
When you let go of the handle, the machine
will shut down automatically. It is impossible
therefore for the saw to run unintentionally.
•
Ensure that you do not cover or block the
ventilation openings whilst working with the
tool.
•
After you have switched off the saw, do
not slow down the saw blade by applying
pressure to its side.
•
Important! Do not put down the machine
until the saw blade has reached a complete
standstill.
Important! Carry out a trial cut in a piece of
waste wood.
6.4 Changing the saw blade (Fig. 12-15)
Warning!
Always remove the battery pack before making
adjustments to the equipment.
Use only saw blades which are of the same type
as the saw blade supplied with this circular saw.
Ask your dealer for advice.
Warning!
Do not use grinding wheels!
The diameters of the saw blades used must
correspond to the diameters speci
fi
ed on the
circular saw blade!
Use only recommended saw blades!
Use the saw blade key (13) supplied to change
the saw blade. The saw blade key (13) is stored
in the housing. If required, pull the saw blade key
(13) out of the housing (see Figure 13).
Important!
For safety reasons, the cordless
circular saw must not be operated with the saw
blade key (13) inserted in it.
•
Press the spindle lock (11).
•
Undo the screw to secure the saw blade (17)
using the saw blade key (13).
•
Push back and secure the moving swing
guard hood (19) using the lever for the swing
guard hood (20).
•
Remove the flange (18) and the saw blade
(12) in a downwards direction.
•
Clean the flange and insert the new saw
blade. Pay attention to the running direction
(see arrow on the guard hood and saw
blade).
•
Tighten the screw to secure the saw blade
(17) and check that the blade runs true.
•
Before you press the On/Off switch, make
sure that the saw blade is correctly fitted
and that moving parts run smoothly and the
clamping screws are tightened securely.
6.5 LED lamp (Fig. 1/Item 5)
The LED lamp (5) can be used in poor lighting
conditions to additionally illuminate the cutting
position. The LED light (5) will come on
automatically as soon as you press the locking
button for the On/O
ff
switch (3).
6.6 Charging the Lithium-Ion battery (not
included)
The corresponding instructions can be found
in the original operating instructions for your
charger.
6.7 Battery capacity indicator (Fig. 10 / item
21)
Press the battery capacity indicator switch (22).
The battery capacity indicator (21) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs lit:
The battery is fully charged.
2 or 1 LED(s) lit:
The battery has an adequate remaining charge.
1 LED
fl
ashing:
The battery is empty, recharge the battery.
All LEDs
fl
ashing:
The temperature of the battery is too low. Remove
the battery from the device and leave it at room
temperature for a day. If the error occurs again,
this means that the battery has been completely
depth-discharged and is defective. Remove the
battery from the device. Never use or charge a
defective battery.
Anl_TE_CS_18_165_Li_USA_SPK7.indb 15
Anl_TE_CS_18_165_Li_USA_SPK7.indb 15
04.05.2022 08:53:19
04.05.2022 08:53:19
