14
6.5 Drill / hammer drill selector switch
(Fig. 7/Item 3)
Change switch position only when the drill is at a
standstill!
Drill
Drill / hammer drill selector switch (3) in the drill
position. (Position A)
Use for: Wood, metal, plastic
Hammer drill
Drill / hammer drill selector switch (3) in the hammer
drill position. (Position B)
Use for: Concrete, rock, masonry
6.6 Tips for working with your hammer drill
6.6.1 Drilling concrete and masonry
n
Switch the Drill/Hammer drill selector switch (3)
to position B (Hammer drill).
n
Always use carbide drill bits and a high speed
setting for drilling into masonry and concrete.
6.6.2 Drilling steel
n
Switch the drill / hammer drill selector switch (3)
to position A (drill).
n
Always use HSS drill bits (HSS = high speed
steel) and a low speed setting for drilling steel.
n
We recommend that you lubricate the hole with a
suitable cutting fluid to prevent unnecessary drill
bit wear.
6.6.3Starting holes
If you wish to drill a deep hole in a hard material
(such as steel), we recommend that you start the
hole with a smaller drill bit.
6.6.4 Drilling tiles
n
To start the hole, switch the drill / hammer drill
selector switch (3) to position A (drill).
n
Switch the drill / hammer drill selector switch (3)
to position B (hammer drill) as soon as the drill
bit has passed through the tiles.
7. Replacing the power cable
If the power cable for this equipment is damaged, it
must be replaced by the manufacturer or its after-
sales service or similarly trained personnel to avoid
danger.
8. Cleaning, maintenance and
ordering of spare parts
Always pull out the mains power plug before starting
any cleaning work.
8.1 Cleaning
n
Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
n
We recommend that you clean the device
immediately each time you have finished using it.
n
Clean the equipment regularly with a moist cloth
and some soft soap. Do not use cleaning agents
or solvents; these could attack the plastic parts of
the equipment. Ensure that no water can seep
into the device.
8.2 Carbon brushes
In case of excessive sparking, have the carbon
brushes checked only by a qualified electrician.
Important! The carbon brushes should not be rep
laced by anyone but a qualified electrician.
8.3 Maintenance
There are no parts inside the equipment which
require additional maintenance.
8.4 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
n
Type of machine
n
Article number of the machine
n
Identification number of the machine
n
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info
9. Disposal and recycling
The unit is supplied in packaging to prevent its being
damaged in transit. This packaging is raw material
and can therefore be reused or can be returned to
the raw material system.
The unit and its accessories are made of various
types of material, such as metal and plastic.
Defective components must be disposed of as
special waste. Ask your dealer or your local council.
GB
Anleitung_TE_ID_750_1_E_SPK7__ 12.11.13 09:35 Seite 14
www.sidirika-nikolaidi.gr
Summary of Contents for 42.596.71
Page 70: ...70 GR z z Anleitung_TE_ID_750_1_E_SPK7__ 12 11 13 09 35 Seite 70 www sidirika nikolaidi gr...
Page 80: ...80 z 2002 96 Anleitung_TE_ID_750_1_E_SPK7__ 12 11 13 09 35 Seite 80 www sidirika nikolaidi gr...
Page 83: ...83 Anleitung_TE_ID_750_1_E_SPK7__ 12 11 13 09 35 Seite 83 www sidirika nikolaidi gr...
