EN
- 8 -
Please note that our equipment has not been
designed for use in commercial, trade or
industrial applications. Our warranty will be voided
if the equipment is used in commercial, trade or
industrial businesses or for equivalent purposes.
4. Technical data
Motor power supply: ............................18 V
Air
fl
ow: ........................... 42.4 CFM (1.2 m³/min)
Sealed suction: .............................33" (Water lift)
Vacuum hose length: ...2.2 to 6.6 ft (0.7 m to 2 m)
Tank capacity: ......................... 2.65 Gallon (10 l )
Weight (Tool only): ...........................6.6 lbs (3 kg)
5. Before starting the equipment
5.1 Assembling the equipment
Fitting the head (Fig. 4)
The equipment head (3) is fastened to the
tank (7) by the locking hook (6). To remove the
equipment head (3), open the locking hook (6)
and take o
ff
the equipment head (3). When
fi
tting
the equipment head (3), make sure that the
locking hook (6) locks into place correctly.
5.2 Fitting the
fi
lters
Important!
Never use the wet/dry vacuum without a
fi
lter.
Always ensure that the
fi
lters are securely seated.
Fitting the foam
fi
lter (Fig. 5/Item 14)
For wet-vacuuming, slip the supplied foam
fi
lter
(14) over the
fi
lter basket (Figs. 3/4).
Fitting the additional
fi
lter (Fig. 6)
For dry vacuum cleaning always use the supplied
additional
fi
lter (16). Fit the additional
fi
lter, so that
no air is sucked through the
fi
lter cage (4) without
being
fi
ltered.
Fitting the dust bag (Fig. 7/Item 15)
For vacuuming
fi
ne, dry dirt it is recommended
that you
fi
t the dust bag (Fig. 7/Item 15). Slip
the dust bag (15) over the vacuuming hole. The
dust bag (54) is suitable for dry-vacuuming only.
The dust bag makes it easier to dispose of the
sucked-in dust.
5.3 Fitting the suction hose (Fig. 1, 3)
Connect the suction hose (10) to the
corresponding connector on the wet/dry vacuum,
depending on the application required.
Vacuuming
Connect the suction hose (10) to the suction hose
connector (8).
Blowing
Connect the suction hose (10) to the blow
connector (9).
5.4 Suction nozzles
Crevice/brush nozzle (Fig. 2)
The crevice/brush nozzle with swing-out brush
(12) is designed for vacuuming solids and liquids
in corners, edges and other areas that are di
ffi
cult
to access.
Upholstery/universal nozzle (Fig. 2)
Fitted with the brush insert (13), the nozzle is
designed for vacuuming solids from upholstery
and carpets. Without the brush insert (13)
fi
tted,
the nozzle is designed for vacuuming solids and
liquids from small to medium-sized surfaces. To
remove the brush insert, press the button and
pull the brush insert o
ff
to the side at the same
time.
Fitting the tool adapter
You can use the supplied tool adapter (Fig. 2/
Item 19) to connect the suction hose (10) to the
tool. To do so,
fi
t it between the suction hose
and the extractor port on the tool. Check that the
connections are secure and air-tight.
Fitting the Lithium-Ion battery (not included)
(Fig. 8)
Open the battery cover (15). To do so,
fl
ip
the cover up as shown in Fig. 8. Then slot the
rechargeable battery (18) into the mount and
push it forward until you hear the battery engage.
Anl_TE_VC_18_10_Li_USA_SPK7.indb 8
Anl_TE_VC_18_10_Li_USA_SPK7.indb 8
13.04.2022 13:57:54
13.04.2022 13:57:54
