GB
GB
- 21 -
You can use the supplied electric tool adaptor
(Fig. 3/22) to connect the suction hose (9) to the
electric tool. To do so, fit it between the suction
hose and the extractor port on the electric tool.
Set the switch (7) on the wet and dry vacuum
cleaner to position AUTO, automatic mode. The
moment you switch on the electric tool, the wet
and dry vacuum cleaner switches on as well.
When you switch off the electric tool, the wet and
dry vacuum cleaner switches off as well after a
pre-set delay.
6.5 Blowing
Connect the suction hose (Fig. 1/9) to the blow
connector (Fig. 2/19) on the wet and dry vacuum
cleaner.
6.6 Filter cleaning system (Fig. 20a-20b)
The equipment has a filter cleaning system which
enables large amounts of fine dust to be suc
-
tioned without fitting the dirt collector bag.
Important!
The filter cleaning system is only allo
-
wed to be activated if the coarse filter is fitted!
Important!
The filter cleaning system can only be
activated if the equipment is in operation!
If there is a drop in suction performance, the filter
cleaning system can be activated at the touch of a
button in order to clean the dirty coarse filter and
increase the suction performance again.
Actuate the cleaning button (1) six times while
the equipment is in operation with the end of the
suction hose. Keep the button pressed down for
4 seconds each time you actuate it. Ensure that
the suction hose does not become kinked when
you do so.
6.7 Cleaning the appliance head (Fig. 1/5)
Clean the appliance regularly with a damp cloth
and some soft soap. Do not use cleaning agents
or solvents; these may be aggressive to the plas-
tic parts in the appliance.
6.8 Cleaning the container (Fig. 1/10)
The container can be cleaned with a damp cloth
and some soft soap or under running water, de-
pending on the amount of dirt.
6.9 Cleaning the filters
Cleaning the pleated filter (Fig. 3/24)
Clean the pleated filter (24) regularly by carefully
patting it and cleaning it with a fine brush or hand
brush.
Cleaning the foam filter (Fig. 3/25)
Clean the foam filter (25) with a little soft soap un
-
der running water and allow it to air-dry.
Cleaning the coarse filter (Fig. 3)
Clean the coarse filter (16) with a little soft soap
under running water and allow it to air-dry.
7. Replacing the power cable
Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
6. Operation
6.1 ON/OFF switch (Fig. 1/7)
Switch position 0:
Off
Switch position I:
Normal operation
Switch position AUTO:
Automatic mode
6.2 Dry vacuuming
Use the pleated filter (24) for dry vacuuming (see
point 5.2). The dirt bag (27) can be fitted in additi
-
on when removing particularly stubborn dirt (see
point 5.3).
If you want to suction large amounts of fine dust,
you can use the coarse filter (16) (see section 5.2
Fitting the coarse filter).
Always ensure that the filters are perfectly secure.
6.3 Wet vacuuming
For wet-vacuuming, use the foam filter (25) (see
point 5.2).
For wet suctioning, fit the sealing ring (37) (see
section 5.2 Fitting the sealing ring).
Check that the filter is securely fitted at all times.
Water drain screw (Fig. 1/11)
To make the tank (10) easier to empty after wet
vacuuming, it is fitted with a water drain screw
(11). Open the water drain screw (11) by turning it
anti-clockwise and drain the liquid.
To empty the container completely and easily, ap-
ply the castor brake (3) and tilt the container.
When wet vacuuming, the floating safety switch
(Fig. 2/21) closes when the maximum tank level
is reached. In doing so, the suction noise of the
equipment will change and become louder.
You must then switch off the equipment and em
-
pty the tank.
Danger!
The wet and dry vacuum cleaner is not suitable
for the vacuuming of combustible liquids.
For wet vacuuming, use only the supplied foam
filter.
6.4 Automatic mode (Fig. 1)
Connect the power cable on your electric tool to
the automatic socket-outlet (4) and connect the
suction hose (9) to the extractor connector on
your electric tool. Check that the connections are
secure and air-tight.
Anl_TE_VC_2350_SACL_SPK13.indb 21
Anl_TE_VC_2350_SACL_SPK13.indb 21
26.01.2021 13:52:58
26.01.2021 13:52:58
