Eiki EK-110U Service Manual Download Page 4

All the safety and operating instructions should be 
read before the product is operated.

Read all of the instructions given here and retain them 
for later use. Unplug this projector from AC power 
supply before cleaning. Do not use liquid or aerosol 
cleaners.
Use a damp cloth for cleaning.

Follow all warnings and instructions marked on the 
projector.

For added protection to the projector during a lightning 
storm, or when it is left unattended and unused for 
long periods of time, unplug it from the wall outlet. 
This will prevent damage due to lightning and power 
line surges.

Do not expose this unit to rain or use near water... 
for example, in a wet basement, near a swimming 
pool, etc...

Do not use attachments not recommended by 
the manufacturer as they may cause hazards.
Do not place this projector on an unstable cart, 
stand, or table. The projector may fall, causing 
serious injury to a child or an adult, and serious 
damage to the projector.
Use only with a cart or stand recommended by 
the manufacturer, or sold with the projector. Wall 
or shelf mounting should follow the 
manufacturer

’s

instructions, and should use a mounting kit 
approved by the manufacturers.
An appliance and cart combination 
should be moved with care. Quick 
stops, excessive force, and 
uneven surfaces may cause the 
appliance and cart combination to 
overturn.
Slots and openings in the back and bottom of the 
cabinet are provided for ventilation, to ensure 
reliable operation of the equipment and to protect it 
from overheating.

The openings should never be covered with cloth or 
other materials, and the bottom opening should not be 
blocked by placing the projector on a bed, sofa, rug,
or other similar surface. This projector should 
never be placed near or over a radiator or heat 
register.
This projector should not be placed in a built- in 
installation such as a book case unless proper 
ventilation is provided.

Never push objects of any kind into this projector 
through cabinet slots as they may touch dangerous 
voltage points or short out parts that could result in 
a fire or electric shock. Never spill liquid of any kind 
on the projector.

Do not install the projector near the ventilation duct 
of air-conditioning equipment.

This projector should be operated only from the type 
of power source indicated on the marking label. If 
you are not sure of the type of power supplied, 
consult your authorized dealer or local power 
company.
Do not overload wall outlets and extension cords as 
this can result in fire or electric shock. Do not allow 
anything to rest on the power cord. Do not locate this 
projector where the cord may be damaged by persons 
walking on it.

Do not attempt to service this projector yourself 
as opening or removing Covers may expose you 
to dangerous voltage or other hazards. Refer all 
servicing to qualified service personnel

Unplug this projector from wall outlet and refer 
servicing to qualified service personnel under the 
following conditions:
a. When the power cord or plug is damaged 

or frayed.

b. If liquid has been spilled into the projector.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally by 

following the operating instructions. Adjust only 
those controls that are covered by the operating 
instructions as improper adjustment of other 
controls may result in damage and will often 
require extensive work by a qualified technician t 
restore the projector to normal operation.

e. If the projector has been dropped or the 

cabinet has been damaged.

f. When the projector exhibits a distinct change in 

performance-this indicates a need for service.

When replacement parts are required, be sure the 
service technician has used replacement parts 
specified by the manufacturer that have the same 
characteristics as the original part. Unauthorized 
substitutions may result in fire, electric shock, or 
injury to persons.

Upon completion of any service or repairs to this 
projector, ask the service technician to perform routine 
safety checks to determine that the projector is in 
safe operating condition.

Information for users in the European Union

This is a device to project images onto a screen,etc., and
is not intended for use as indoor lighting in a domestic
environ- ment.

Directive

2009/125/EC.

NOTE FOR CUSTOMERS IN THE US

Hg LAMP(S) INSIDE THIS PRODUCT CONTAIN 

MERCURY AND MUST BE RECYCLED OR DISPOSED OF 
ACCORDING TO LOCAL STATE OR FEDERAL LAWS.

Safety Instructions

4

Summary of Contents for EK-110U











































Reviews: