Eighteeth MotorTurbo User Manual Download Page 23

12

EMC Tables

Page 23 / 30

12.EMC Tables

Guidance and manufacturer’s declaration - electromagnetic emissions

The MotorTurbo is intended for use in the electromagnetic
environment specified below. The customer or the user of the
MotorTurbo should assure that it is used in such an environment.

Emissions test

Complian-ce

Electromagnetic
environment guidance

RF emissions CISPR
11

Group 1

The MotorTurbo uses RF
energy only for its internal
function. Therefore, its RF
emissions are very low and
are not likely to cause any
interference in nearby
electronic equipment.

RF emissions CISPR
11

Class B

The MotorTurbo is suitable
for use in all
establishments, incl- uding
domestic establishents and
those directly connect- ed
to the public low voltage
power supply network that
supplies buildings used for
domestic purposes.

Harmonic emissions
IEC61000-3-2

Class A

Voltage
fluctuations/flicker
emissions
IEC 61000-3-3

Complies

Guidance and manufacturer’s declaration – electromagnetic
immunity
The MotorTurbo is intended for use in the electromagnetic
environment specified below. The customer or the user of the
MotorTurbo should assure that it is used in such an environment.

Immunity test

IEC 60601
test level

Compliance
level

Electromagnetic
environment -
guidance

Summary of Contents for MotorTurbo































Reviews: