>> BACK PANEL
22 POWER RECEPTACLE
Connect the supplied AC power cord to the power recep-
tacle. Make sure the Euro plug is firmly inserted in the
socket. The other end of the cable should be connected
to any standard grounded AC outlet or into a power strip
of proper voltage. Before you plug in do make sure that
the voltage is correct (see #23)!
Just in case you lose the cord provided, the jack accepts
a standard 3-prong IEC cord like those found on most
professional gear and computers – you can get it at any
electronics, music or computer store.
Never (!) remove or otherwise attempt to defeat
the ground pin of the power cord in order to get rid
of a hum induced by a ground loop.
22a POWER FUSE
The T 1000 is fused for your and its own protection. If
you suspect a blown fuse, disconnect the cord, pull out
the »FUSE DRAWER« (#22a, located just below the cord
receptacle) and replace the fuse with another suitable
fuse. There should be a spare fuse in the fuse drawer.
For 230 V and 115 V units the fuse for the T 1000 must
be a 6,3 A (amps) SLO BLO 5 x 20 mm. When you’re in
a country with a standard of 115 volts set the »VOLTAGE
SELECTOR« (#23) accordingly.
If two fuses blow in a row, something is very wrong. Do
not open the unit. Refer service to qualified service per-
sonnel.
23 VOLTAGE SELECTOR
The T 1000 features a “VOLTAGE SELECTOR” allowing
you to use your amplifier anywhere in the world just by
the flick of a switch. The unit is set to 230 V when we
ship to a country in Europe.
Should you wish to use your T 1000 in the USA set the
“VOLTAGE SELECTOR” to “115 V”.
ATTENTION: Don’t forget to set it back to »230 V«
when you return home! EICH Amplification can-
not be made responsible for damages to the unit
caused by improper voltage selection. Therefore
it is a good idea to always check the »VOLTAGE
SELECTOR« before powering up the unit.
24 SPEAKER BRIDGED MODE
T 1000 sports three original Neutrik Speakon® NLJ2MD-
V speaker outputs. The wiring of the pins is as follows:
1+ = hot, 1- = ground. The one on the right (looked from
behind) is reserved for mono bridged operation. When
operating the amp in »BRIDGE MODE« care should be
taken that the minimum load is no less than 4 ohms.
24a BRIDGED MODE
Press the switch »BRIDGE MODE ON/OFF« just above
this Speakon® output until it rests in the »ON« positi-
on. In this mode neither the two »VOLUME« controls for
»CHANNEL A« (#26a) and »CHANNEL B« (#25a) nor the
»SUB-BOOST« filter (#25b) are active. The overall output
level is controlled by the »MASTER« volume control (#15)
on the front panel only. Make sure that the speaker out-
puts of »CHANNEL A« (#26) and »CHANNEL B« (#25) are
not being used.
In »BRIDGE MODE« the two internal power amps are
combined to produce 1000 watts of continuous output
power at a minimum load of 4 ohms. Be absolutely cer-
tain that the speaker cabinet(s) connected is (are) able
to handle the extremely high output power of the amp.
All EICH cabinets featuring at least 4 speakers will do
the job easily (e.g. 410L-4, 610L-4, 810L-4, 612XL-4 etc.).
When you use a speaker cabinet with a lower power
handling capacity do make sure that you operate the amp
at moderate levels only, i.e. don’t turn up the »MASTER«
control (#15) too far.
Whatever your setup is, always make sure that the spea-
ker cables are as long as necessary but as short as pos-
sible, using heavy gauge cable (we recommend at least
2 x 2.5 mm2). Do stick to speaker cables with Speakon®
connectors only, either NL2FX (two pin connector) or
NL4FX (four pin connector). The wiring of the pins is as
follows: 1+ = hot, 1- = ground. High quality EICH speaker
cables can be obtained as an option.
25 CHANNEL B
T 1000 is equipped with two power amps, »CHANNEL A«
(#26) and »CHANNEL B« (#25), which can be used simul-
taneously, each of them delivering 500 watts continuous
output power at a minimum load of 2 ohms. Each power
11
10
-10
0
VOLUME
-10
0
VOLUME
SUB
OFF
ON
OFF
ON
N
E
UTRI
K
N
E
UTRI
K
N
E
UTRI
K
SEND
EFFECTS LOOP
RETURN
LINE OUT
LINE IN
TUNER
!
HIGH VOLTAGE! CAUTION: TO PREVENT
THE RISK OF FIRE AND SHOCK HAZARD
DON’T EXPOSE THIS APPLIANCE TO
MOISTURE OR RAIN. DO NOT OPEN CASE.
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
MIN. 2 Ω
MIN. 2 Ω
MIN. 4 Ω
CHANNEL
A
CHANNEL
B
BRIDGED MODE
USE ONLY WITH A 250V FUSE
VOLTAGE
SELECTOR
230
FUSE
230/115 V
T6,3 A (SB)
REHEARSAL
AUX IN
Made in Germany
22
26
31
30
29a
25
24
28
29b
22a
27
23
26a
25a 25b
24a
