background image

32 

Phone:(910) 392

2490 

Fax: (910) 392

2123 

416 Landmark Drive 
Wilmington, NC 28412 

www.easterninstruments.com

 

  

 
ZERO PROCESS TEMPERATURE 
 

This is a procedure for zeroing the Process Temperature which is 
displayed under the screen T.  The 

fi

rst step is to ensure that the 

sensor is registering 0 deg C by u lizing a 0 deg C (32 deg F) Tem

perature Simulator (provided).  A picture of the Temperature 
Simulator can be seen to the right.  The second step is to actual

ly zero the value using the Bu ons/LCD Screen.  
 

NOTE: DO NOT ZERO WITHOUT SIMULATING 0 DEG C OR      
ENSURING YOUR PROCESS TEMPERATURE IS 0 DEG C.  IF THE 
TRANSMITTER IS ZEROED WHEN THE TEMPERATURE IS NOT 0, 
YOU WILL INTRODUCE ERROR INTO YOUR MEASUREMENT. 

 

 

Using the 0 deg C Temperature Simulator 

 
1. 

Remove power from the QVT. 

Wiring the QVT while the 

QVT has power turned on can result in damage to the LCD 
Board and can cause failure of the QVT. 

2. 

Remove the QVT Cover.

 

3. 

Remove the LCD Board.  

A detailed descrip on of this proce

dure can be found in the Electrical Installa on sec on of this 
manual.   

4.  Looking at the RTD Connector, 

remove the Female Connect

or from the Male Header

 so that the RTD is no longer con

nected to the QVT. 

5.  The Temperature Simulator contains a duplicate Female 

Connector.  

Place the Female Connector of the Tempera

ture Simulator into the RTD Connector’s Male Header and 
push un l you hear it click.  

 

6. 

Replace the LCD Board

 

7. 

Return power to the QVT.

 

 

Performing a Zero for Temperature 

  
1.  Once a Zero, using the Temperature Simulator has been per

formed (as outlined above) 

Press the Program Bu on un l 

the T Process Temperature screen is displayed (Screen #1).

 

2. 

Press and hold the Zero Bu on for 5 seconds.  

This will 

open up the Temperature Zero screen.  The Temperature 
Zero screen will look like screen #2.  The screen will 

fl

ash on 

and o

 

 

#1 

#2 

#3 

4

20 mA 

Connector 

The RTD 

Connector 

Board Snap Mounts 

Summary of Contents for QVT










































Reviews: