EHRET FSL-light Installation Instructions Manual Download Page 4

4

Important notes

Explanation of signs and symbols

Warning notes

 

DANgEr

  Designates an imminent danger that 

could lead to death or severe injuries if 
the respective precautionary measures 
are not implemented.

 

WArNINg

  Means that death, severe bodily injury or 

major property damage could occur if the 
respective precautionary measures are 
not implemented.

 

CAutIoN

  Means a possible danger that could lead 

to minor injuries or property damage if it 
is not avoided.

   Directives for action

Safety notes

  

only qualified specialist personnel may 
carry out installation and commission-
ing!

 

WArNINg

Incorrect installation could lead to se-
vere injuries and/or damage to property.

  Follow all installation instructions.

 

WArNINg

  take into account the following notes 

and warnings in order to avoid dangers 
and to protect the product.

   observe the accident prevention regulations 

of the Accident prevention & Insurance As-
sociation.

   observe the rules of the road during trans-

port.

   Make sure that the load is well-secured on 

the means of transport.

  cordon off a generously large area around 

the installation site.

  observe without limitation the regulations 

of the manufacturers of dowel and fitting 
materials.

   the mounting bases of the installation site 

are to be checked for load-bearing capacity 
prior to installation.

  

In the event of uncertainties about the 
mounting bases, contact your responsible 
building experts.

   check the product for damage prior to instal-

lation. products requiring repair may not be 
used.

Summary of Contents for FSL-light





















Reviews: