EHOMEXPERT EHFT-2104BN Assembly Instructions Manual Download Page 11

REPLACEMENT PARTS LIST 

 

N

O

I

T

P

I

R

C

S

E

D

 

#

T

R

A

P

 

O

N

Left panel

A
B
C
D
E

F

L-365
F210004-A-B

F210004-A-D
F210004-A-E
F210004-A-F
F210004-A-G

G

Door panel
Front panel
Back-left leg

F210004-A-H

H

Back-right leg

F210004-A-I

I

Front-right leg

J
K
L

F210004-A-J

Front-left leg

ANES-GV

Firepit gas valve

F210004-A-K

Gas cylinder support

ET-T-250

Firepit thermocouple, 250 mm/10"

ET-FL03

Firepit foot leveler 03, 32 x 23 mm

ET-E3-300

Firepit electrode 1.75" tip, wire 300 mm 

for 30000 BTU

CLTN-PLSELT

Firepit pulse ignition

EFP-CNNB

Firepit control knob ET, large #6

FM-LVRK-6.6

Firepit lava rock (red), 6.6 lbs

M

F210004-M

Weather cover

N

EFP-DH

Firepit door handle ET

Firepit ET square lid 365mm x 9mm
Table top assembly

F210004-A-C

Back panel

CARE AND MAINTENANCE

   

To enjoy the outstanding performance from your fire pit, make sure you perform the following activities on a regular 

basis:

1. Use warm soapy water for cleaning. Never use flammable or corrosive cleaning agents.

2. While cleaning the fire pit, make sure to keep the area around the burner dry at all times. DO NOT submerge the 

    control valve assembly. If the gas control is submerge in water, DO NOT use it. It must be replaced.

3. Air flow must be unobstructed. Keep controls, burner, and circulating air passageways clean. Signs of possible 

    blockage include:

    (1). Gas odor with extreme yellow tipping of flame.

    (2). Fire pit does NOT reach the desired temperature.

    (3). Fire pit flame is excessively uneven.

    (4). Fire pit makes popping noises.

    (5). Spiders and insects can nest in burner or orifice. This dangerous condition can damage fire pit and render it 

           unsafe for use. Clean burner holes by using a heavy-duty pipe clearer. Compressed air may help clear away 

           small particles.

4. Carbon deposits may create a fire hazard. Clean burner with warm soapy water if any carbon deposits develop.

5. Cover your fire pit with an outdoor weather cover when not in use to protect it from the elements.

NOTE: 

Always allow fire pit to cool COMPLETELY before you cover the fire pit with an outdoor weather cover or you 

attempt to service or perform maintenance.

11

Summary of Contents for EHFT-2104BN













Reviews: