the water and the bottom of the filter. Attention: Filter must always be operated in an upright posi-
tion only.
Burning danger! Be careful when touching the heating coil of devices with integrated heater.
Take the necessary precautions when handling components that can discharge static electricity.
Do not clean the unit – or parts of it – in the dishwater. Not dishwater resistant!
Do not dispose of this product as normal household waste. Take it to your local refuse collection
side.
The product is qualified in accordance with the respective national regulations and guidelines and meets
EC standards.
max.
180 cm
2. Component overview (see II)
1.
Set the locking lever (12) to
„OFF“
and press the adapter bar (18) until the safety adapter (13) disengages.
2.
Open the locking clips (9) by pulling the clips’ lower edge.
3.
Remove the pump head (17).
4.
Remove all
inserts.
Caution:
Do not overfill filter inserts as, otherwise, their accurate fit is no longer assured.
5.
Fill the
lowest filter insert with
EHEIM
MECH or
EHEIM
bioMECH.
6.
Fill the middle filter inserts with
EHEIM
SUB-
STRAT
pro
.
7.
Rinse the filled filter inserts with water.
8.
Re-insert the filter inserts in the filter tank (10) (
EHEIM
MECH or
EHEIM
bioMECH).
9.
Place the white filter fleece (6) on the top filter insert.
10.
Place the cover grat-
ing (5) on the white filter fleece (6).
11.
Insert the prefilter (3) with the blue filter mat (1) (place onto supports
➞
arrows).
12.
Attach the pump head (17) (observe fitting position) and close the locking clips (9).
Note:
Use original
EHEIM
hoses only.
13.
Attach the pre-assembled hose accessories (see
I
). to the aquarium.
14.
Cut the hoses (23) to length in ac-
cordance with the clearance between the filter and the aquarium and plug onto the accessories.
15.
Plug the
hoses (23) onto the safety adapter (13) down to the limit stop.
16.
Attach the hose locking device (11).
17.
Push the safety adapter (13) into the pump head (17) until it audibly latches.
18.
Set the locking lever (12) to
„ON“
.
19.
Assure the the nozzle pipe (25) is suspended above the water surface.
20.
Rapidly press the suction
aid (16) several times consecutively until the filter tank (10) automatically fills with water (no water must be pre-
sent in the prefilter!).
21.
Plug in the power supply unit (28) at the pump head (17).
22.
Plug in the power cable
(30).
23.
For bleeding, press the suction aid (16) once or twice and push the nozzle pipe (25) to the desired
position.
3. Connection and commissioning
1.
Filter mat blue
2.
Prefilter seal
3.
Prefilter
4.
Prefilter flap
5.
Cover grating
6.
Filter pad white
7.
Filter
inserts
8.
Partition wall
9.
Locking clips
10.
Filter tank
11.
Hose locking device
12.
Locking lever
13.
Safety
adapter
14.
Bracket
15.
Float
16.
Suction aid
17.
Pump head
18.
Adapter bar
19.
Control panel
20.
Profile
seal
21.
Pump wheel
22.
Pump cover
23.
Hoses
24.
Outlet elbow
25.
Nozzle pipe
26.
Suction pipe
27.
Sucker with terminal clamp
28.
Power supply unit
29.
Suction basket
30.
Power cable
7
Note:
For electronic operation (
professionel 3
e
) use the „operating instructions electronics“.
4. Operation
Note: Electronic version (
professionel 3
e
)
:
The control panel indicates the filter elements to be cleaned. Implement maintenance works in case of re-
duced filter capacity (approx. every 3 to 6 months).
First, clean prefilter (6.1).
If prefilter cleaning insuf-
ficient: Clean all filter inserts (general cleaning 6.2).
If general cleaning insufficient: Clean the pump cham-
ber (6.3).
5. Maintenance and care
Summary of Contents for Professionel 3e 2076
