manualshive.com logo in svg

EHC Fusion E10 Combi Series, Installation And Technical Manual, Page: 27 / 33

Share
Download
EHC Fusion E10 Combi Series Installation And Technical Manual Download Page 27

EHC 

Fusion E10 Combi

–

Installation and technical manual

Page 27

15.

Commissioning: Fusion boiler instructions/Cont.____

Front Control Panel

Indicator B

When GREEN light is on the pump is operating. When this light flashes the flow rate
is insufficient (less than 5 ltr per min) Refer to technical specifications

Indicator C

When light is off room thermostat temperature has been achieved. (RP is open) 
When the green light flashes the NA connection is open. (na should always have link 
installed)
When RED light is on, the boiler is operating
When GREEN light is on boiler temperature has been achieved.

Indicator F

Set Temperature

Indicator D

Return Temperature
When this indicator flashes the return temperature sensor is faulty.

Indicator E

Flow Temperature
When this indicator flashes the flow temperature sensor is faulty.

Indicator G

Press to show Flow, Return and Set Temperature

Indicator H

Press to check flow rate

Indicator I

Press to check power consumption

Indicator A

DHWC Indicator

Summary of Contents for Fusion E10 Combi Series


































Reviews:

No comments