manualshive.com logo in svg

Eggtimer Rocketry Eggtimer Classic, Assembly Manual

Share
Download
Eggtimer Rocketry Eggtimer Classic Assembly Manual Download Page 2

 

 

 

Before You Start… 

 
• Go to our web site at 

www.eggtimerrocketry.com

 and download the latest Release Notes. 

 
• Go to our web site at 

www.eggtimerrocketry.com

 and download the latest Assembly 

Instructions. 
 
• Read them thoroughly before starting… it will save you some grief later, we promise! 
 
• We recommend that you apply the latest Flash Updates after validating your Eggtimer’s 
operation; you should do this BEFORE you perform a Master Reset (since it may affect how 
memory is used) 
 
• 

Before you can program or fly your Eggtimer, you need to perform a Master Reset.  See 

Appendix A in the Eggtimer Users Guide for details. 

 
 

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 
 
Thanks for buying an Eggtimer flight computer!   We’re sure that you are ready to get started, 
but before you do you will need to get some tools together.  The tools that you will need are: 
 
___ 

Low-wattage soldering iron, 15W or less, with a fine tip 

 
___ 

Fine rosin-core solder, .022”-.032”, 60/40 tin-lead or similar lead-free solder 

 
___ 

Small needle-nose pliers 

 
___ 

Small diagonal cutters 

 
___ 

A small damp sponge for cleaning the tip of your soldering iron 

 
___ 

A lighted magnifier, for inspecting solder joints  (not essential, but very helpful) 

 
___ 

A well-lighted place to work, preferably with a wood or metal surface, 

 

  also preferably not carpeted 

 

Summary of Contents for Eggtimer Classic


























Reviews:

No comments

Brands by name

Popular brands

Load more brands