Ega Master 79607 Operating Instructions Manual Download Page 8

8

Pay attention that the circlip locks in the groove of the tool. Only use tools with suitable shank 

(see “Technical Specification).

Remove tool

Pull the tool from the tool holder. Stucking tools can be loosened by slight beats with a rubber 

hammer.

Change tools

When inserting a tool, pay attention that it is properly seated on the tool holder.

If the tool is not firmly fixed to the tool holder, it can unscrew and cannot be controlled 

anymore.

Before each operation, make visual check of the machine and machine tools, as well as 

accessories with regard to integrity and appropriateness for the application.

Never operate the machine if one or more parts (e. g. machine tools, cables, lines) are damaged, 

if it is not working properly, if any damages can be identified or are to be suspected (e. g. after it 

has been dropped).Replace damaged parts immediately.

Never remove protective devices from the machines where fitted.

Ensure they are in good condition and properly adjusted before starting the machine.
A malfunction, which impairs operator safety, must be immediately removed.
Pay attention that the machine is cleaned from dust and deposits of rust particles and other 

deposits before and after the work.

Torques

The torque adjustment is done via the air pressure.

3 bar

3,5 bar

4 bar

5 bar

6 bar

Setting

Md

n

Md

n

Md

n

Md

n

Md

n

1

175

3

250

3

275

4

300

5

325

5

2

275

6

325

6

350

6

450

7

500

7

3

400

7

475

7

550

8

700

10

700

10

4

500

8

550

8

650

10

750

12

750

12

The torque values are guide values only, they depend basically on the application, the flow 

pressure and the applied accessories.

BASIC SAFETY INSTRUCTIONS

Read operation instructions/safety instructions!

Before working on or with the tool, read the safety instructions and follow the 

instructionsduring operation.

Do not modify machine or machine tools and accessories after receipt. Permission from the 

manufacturer must be obtained before any modifications or alterations are done in compliance with 

all safety instructions. Use the machine only for its intended use. Observe the technical data of the 

equipment and the ambient temperatures. Pay attention to labels, restrictions of use and special 

instruction notes on the machine tools and the machine itself. Regularly check that the type plate 

and symbols on the machine are legible.

Summary of Contents for 79607























Reviews: