manualshive.com logo in svg

Efco Swaploader SL-330, Parts And Operation Manual

The Efco Swaploader SL-330 is a versatile and reliable equipment designed for efficient waste management and load handling. Ensure smooth operations with the comprehensive Parts and Operation Manual, readily available for free download at our website. Maximize productivity and convenience with this essential manual.

Share
Download
background image

 

SL-330.INS

 

 

 

 

 

 

 

2-15

 

09/2009 

 

HYDRAULIC TANK INSTALLATION 

 
1. 

Select a location to mount the hydraulic tank.  Reference Figure G or Drawing No. 
90H57 for the suggested location of the hydraulic tank to the rear of the control valve 
assembly on the left-hand side of the truck.  The hydraulic hoses have been sized for the 
tank to be mounted in this general area.  The tank can be located on the right-hand side or 
behind the cab, if necessary, which means longer hoses may be required. 

 
2. 

Drill four (4) holes for 1/2-inch diameter bolts (provided) in the mount angle of the 
hydraulic tank (two per angle) and the frame rails of the truck chassis.  Mount the 
hydraulic tank and install the hydraulic filter.  Install the hydraulic return hose and the 
hose barb fitting between the filter and the control valve assembly as shown on Drawing 
No. 91H03.  The hose length can be shortened if necessary.  Secure the hose to the barb 
fittings with the hose clamps provided. 

 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 

Figure G 

Summary of Contents for Swaploader SL-330







































































































































Reviews:

No comments

Related manuals for Swaploader SL-330

U-Line H-2708 Quick Start Manual preview
H-2708
Brand: U-Line Pages: 3
Parkside PUTK 50 B1 Operating Instructions Manual preview
PUTK 50 B1
Brand: Parkside Pages: 43
Omnia Rotatruck 11-23AT/26 Converting Instructions preview
Rotatruck 11-23AT/26
Brand: Omnia Pages: 7
U-Line H-3200 Quick Start Manual preview
H-3200
Brand: U-Line Pages: 6
Oshkosh SIEMENS ESPREE 1.5T Operator'S And Service Manual preview
SIEMENS ESPREE 1.5T
Brand: Oshkosh Pages: 142
Noblift SPT15 Series Operating Instructions & Parts List Manual preview
SPT15 Series
Brand: Noblift Pages: 26

Brands by name

Popular brands

Load more brands