Edwards Porta Power Safety & Instruction Manual Download Page 12

2

This manual provides installation information for the following:

25 Ton 

40 Ton 

50 Ton

55 Ton 

60 Ton 

65 Ton

75 Ton 

100 Ton 

100 Ton DX

120 Ton 

Elite 110 

Elite 110/65 D.O.

Porta Power

Environmental Requirements at Work Station

The work station environment for your machine must meet the following 
minimum requirements:

• Floor 

area: 

Assure that the machinery work area provides 

for a stable, adequately sized and load rated fl oor area for 
material movement to and from the machinery work stations.

• Shelter: 

Edwards Ironworkers are designed for indoor use 

only. Protect your Ironworking machinery from water, salts 
and corrosive elements.

• Lighting: 

500LUX (50 footcandles) minimum.

• Operating 

Temperature: 

This equipment will operate  

correctly in its intended ambient, at a minimum between  
+5° C and +40°C.

• Relative 

Humidity: 

This equipment will operate correctly 

within an environment at 50% RH, +40°C. Higher RH may 
be allowed at lower temperatures. Measures shall be taken 
by the Purchaser to avoid the harmful effects of occasional 
condensation.

• Altitude: 

This equipment will operate correctly up to 1000m 

above mean sea level.

• 

Transportation and Storage: 

This equipment will withstand, 

or has been protected against, transportation and storage 
temperatures of -25°C to +55°C and for short periods up to 
+70°C. It has been packaged to prevent damage from the 
effects of normal humidity, vibration and shock.

Electrical Requirements at Work Station

Locate your Porta Power directly adjacent to your power supply. Con-
fi rm that power supply is not connected in series with other machinery. 
Provide dedicated electrical socket and circuit breaker for each machine 
installed. Edwards Machines are protected from voltage variations pro-
vided the variation does not /- 10% machine rating.

Installation Requirements

Electrical Performance Specifi cation

 

Machine 

Motor 

Type Brand 

60Hz/V FLA 

50Hz/V FLA

 

25 Ton

 

116676

 

1Hp 1~

 

Leeson

 

60 Hz 115/208-230

 

12/6

 

50 Hz 110/220

 

13/6

  40, 50, 55, 60 Ton,  132089 

5Hp 1~ 

Leeson 

60 Hz 230 

19 

50 Hz 208-220 

23-22

  Porta-Power 

132077 

5Hp 3~ 

Leeson 

60 Hz 208-230/460 

14/7 

50 Hz 190/380 

16/8

   

CEM3615T-5 

5Hp 3~  

Baldor 

60 Hz 575 

5

  65, 75, 100 Ton, 

132089 

5Hp 1~ 

Leeson 

60 Hz 230 

19 

50 Hz 208-220 

23-22

  Elite 110 

140809 

7.5Hp 3~ 

Leeson 

60 Hz 208-230/460 

22-21/10 

50 Hz 190/380 

24/12

  Elite 110/65 D.O. 

CEM3710T-5 

7.5Hp 3~  

Baldor 

60 Hz 575 

8

   

141140 

7.5Hp 1~  

Leeson 

60 Hz 230 

36

  100DX, 120 Ton 

CEM3714T 

10Hp 3~ 

Baldor 

60 Hz 208-230/460 

25-24/12

   

EM3714T-5 

10Hp 3~  

Baldor 

60 Hz 575 

10

   

CEM3714T-50 

10Hp 3~  

Baldor 

 

 

50 Hz 220/380/440 

28/16/14

   

CL3712T 

10Hp 1~ 

Baldor 

60 Hz 208-230 

38

Summary of Contents for Porta Power


































Reviews: