Edwards nXDS10i nXDS15i Instruction Manual Download

Page: 34 / 58

Figure 9 User interface panel

1. Mains power connector

2. Power connected indicator

3. Start button with indicator

4. Standby button with indicator

5. Increase standby speed button with

indicator

6. Decrease standby speed button with

indicator

7. Auto

‑

run enabled indicator

8. Service indicator

9. Alarm indicator

10. 15

‑

way D

‑

type connector

11. USB port (Service mode only)

12. Stop button

1. Mains power connector

2. Power connected indicator

3. Start button with indicator

4. Standby button with indicator

5. Increase standby speed button with

indicator

6. Decrease standby speed button with

indicator

7. Auto

‑

run enabled indicator

8. Service indicator

9. Alarm indicator

10. 15

‑

way D

‑

type connector

11. USB port (Service mode only)

12. Stop button

5.2.1 Start and stop

Use the buttons (

Figure: User interface panel on page 32

, items 3 and 12) to start and

stop the pump. Note that the stop command does not isolate the pump from the

electrical supply.

5.2.2 Standby

Operation at reduced speed will further improve tip seal and bearing service life.

Vacuum performance will be reduced when operating at standby speed.
Press the Standby button to select standby mode. The pump will initially run at factory

default standby speed (70% of full speed). The speed can be adjusted using the increase

and decrease standby speed buttons. The maximum standby speed is 100% of the

default run speed and the minimum standby speed is 67% of the default run speed. A

single short push will change the speed by 1% of the default run speed, holding the

button will change the speed by 1%/sec. Once adjusted, the pump will return to this new

user

‑

defined speed each time standby speed is selected.

The Standby button must be pressed to return to normal run speed.

Page 32

A73501880_G - Operation

Summary of Contents for nXDS10i nXDS15i



























































Search results

Summary of Contents for nXDS10i nXDS15i

Reviews:

Related manuals for nXDS10i nXDS15i

Brands by name

Popular brands

Edwards nXDS10i nXDS15i, Instruction Manual

Search results

Summary of Contents for nXDS10i nXDS15i

Reviews:

Related manuals for nXDS10i nXDS15i

Brands by name

Popular brands