Edwards iXL1000 Instruction Manual Download Page 59

Page: 59 / 70

Page 51

Edwards and the Edwards logo are trademarks of Edwards Limited.

Appendix A1

A540-55-880 Issue D

By default the 4 parameters displayed in the Normal menu are as shown above but these may be changed via the Edit
Display attributes menu, accessed from the

SETUP menu.

A1.4.2

Status menu

Press the

Status

button to enter. Scroll by pressing up/down keys. Press

CANCEL

to exit back to

Normal

menu.

If a device is not fitted the associated parameters will not be displayed. Parameters displayed:

A1.4.3

SETUP menu

Press the

Setup

button to enter. Menu title is shown at the top of the display. Scroll by pressing up/down keys. Press

ENTER

to open a sub menu or

CANCEL

to exit back to

Normal

menu.

Table A4 - Status menu

Description

Typical Display

Serial Number

S/N 1234567

Control Holder

NONE IN CONTROL

Dry Pump current

DP CURRENT

1.1A

Booster current

MB CURRENT

1.1A

Green Mode state

Green Mode STATE

Off

Dry Pump temperature

DP TEMP

100C

Booster Temperature

MB TEMP

100C

Booster MB End Cover temperature

MB E/C TEMP

100C

Flow Rate

FLOW

44 slm

Dry Pump Power

DP POWER

1.1 kW

Booster Power

MB POWER

1.1 kW

Dry Pump speed in percent

DP SPEED

100 %

Dry Pump speed in Hz

DP SPEED

100 Hz

Booster speed in percent

MB SPEED

100 %

Booster speed in Hz

MB SPEED

100 Hz

Dry Pump Inverter Temperature

DP INV TEMP

100C

Booster Inverter Temperature

MB INV TEMP

100C

Run Hours

RUN HOURS

1000

Number of Pump Starts

PUMP STARTS

100

Time to Stop (seconds)

TIME TO STOP

900

Active Alarms and Warnings (if present)

Table A5 - SETUP menu

Description

Display

Commands menu

Command Menu…

Display Inverter Fault History menu

Inv Fault Hist…

Software Version Display menu

S/W Version…

Display Serial Number

Serial Num…

Fit Accessory menu

Fit Accessory…

Edit IP configuration menu

IP Config…

Summary of Contents for iXL1000


































































Search results

Summary of Contents for iXL1000

Reviews:

Related manuals for iXL1000

Brands by name

Popular brands

Edwards iXL1000, Instruction Manual

Search results

Summary of Contents for iXL1000

Reviews:

Related manuals for iXL1000

Brands by name

Popular brands