manualshive.com logo in svg

Edwards CXS, Instruction Manual, Page: 17 / 40

Share
Download
Edwards CXS Instruction Manual Download Page 17

© Edwards Limited 2016. All rights reserved. 

Page 9

Edwards and the Edwards logo are trademarks of Edwards Limited.

Operation

D397-53-880 Issue C

4

Operation

4.1

Profibus system information

The Profibus module is for connection to a Profibus DP network and operates as a V0 slave only.

The Profibus master requires a GSD file for each slave. The GSD file for this slave is contained on the CD supplied
with the unit and has the file name "EDW0C5F.GSD", which is registered with the Profibus Association.

When configuring your system the "ID" number will be 0C5F and the unit's description will be “Edwards_GXS/
CXS_Pump”.

Note:

The GSD file should not be altered.

4.2

Quick start set up instructions

1. Install the module and connect the cables as described in 

Section 3

.

2. Set the address switches on the Profibus module. See 

Section 4.4

.

3. Apply power (or power cycle the Profibus Module, for example by disconnecting then reconnecting the power

connector).

4. Load the GSD file into your Profibus system configurator.

5. Select "Edwards_GXS/CXS_Pump" as a slave and set the address to match the address switches.

6. Select Module 11 to provide on and off control of the pump and select Module 992 to monitor pump alert state.

Add other Profibus software modules as required.

4.3

Front panel display

Figure 6 - Profibus front panel display

Summary of Contents for CXS









































Reviews:

No comments