Edwards A705-41-000, Instruction Manual

Page: 81 / 82

Index
A705-40-880 Issue B
© Edwards Limited 2011. All rights reserved. Page 75
Edwards and the Edwards logo are trademarks of Edwards Limited.
A
Abnormal operation .......................................8
Accessories ........................................... 7
,
73
Adjust the pump coolant jacket trip temperature
(pumps fitted with a temperature transmitter, if re-
quired)
.................................................... 29
Adjust the TCV (thermostatic control-valve) ....... 30
Adjust the thermal snap-switch (if fitted) .......... 29
Allow the pump to warm up ........................... 32
ATEX system control .................................... 31
C
Change the pump oil and clean the oil-level sight-glass-
es
.......................................................... 40
Check for coolant leaks ................................ 46
Check the coolant level and refill if necessary ..... 45
Check the direction of pump rotation ................ 23
Check the gearbox oil-level ............................ 20
Check the gearbox oil-level and fill the gearbox with oil
(if necessary)
............................................. 36
Check the shaft-seals purge supply ................... 37
Clean the cooling system ............................... 51
Clean the cooling-water filter ......................... 51
Clean the cooling-water flow indicator .............. 51
Clean the heat exchanger .............................. 53
Clean, inspect and relubricate the rotor bearings . 43
Commission the pump .................................. 29
Commissioning procedure .............................. 29
Connect the cooling-water supply .................... 25
Connect the electrical supply to the pump-motor . 21
Connect the pump coolant jacket temperature sensor
introduction 21
Connect the pump-inlet and outlet ................... 27
Connect the pump-inlet to your process system ... 27
Connect the pump-outlet to your exhaust system . 28
Connect the shaft-seals purge nitrogen supply ..... 25
Connect the temperature transmitter (if fitted) ... 22
Connect the thermal snap-switch (if fitted) ........ 22
Connections .............................................. 13
Cooling-water data ...................................... 11
D
Disposal ................................................... 71
Drain the coolant from the cooling system .......... 51
Drive coupling operation .................................3
Drive operation ............................................3
E
Electrical connections .................................. 20
Electrical data ........................................... 10
F
Fault finding .............................................. 68
Fill the pump with a different coolant ............... 45
Fit a replacement service module .................... 63
Fit the coupling cover to the new pump-motor .... 58
Fit the new service module ............................ 65
Flush a pump which has been operating ............. 46
Flush a seized pump .................................... 48
Flush the pump with cleaning solution .............. 46
H
Hazardous area and safe area versions of the pump 7
I
Inspect and reset the torque limiter (pumps with a
torque limiter only)
..................................... 33
Inspect the components removed from the service
module
.................................................... 65
Inspect the pipelines and connections ............... 39
Inspect the pressure relief valve and replace the hinge
bushes, flap and O-ring (if necessary)
EDP250 and EDP400 only 39
Inspect the torque limiter ............................. 54
Installation ............................................... 17
L
Leak test the installation .............................. 28
Leak test the pump ................................ 40
,
44
Locate the pump ........................................ 18
Lower the pump-motor and coupling cover (with the
motor change frame)
................................... 55
Lower the pump-motor and coupling cover (without
the motor change frame)
.............................. 54
Lubrication data ......................................... 12
M
Maintenance ............................................. 35
Maintenance plan ....................................... 35
Materials of construction .............................. 16
Mechanical data ......................................... 10
N
Noise data ................................................ 12
Non-ATEX system control .............................. 32
Normal operation ..........................................7
O
Operating and storage conditions ......................9
Operation ................................................. 31
Operational safety ...................................... 31
Ordering options ..................................... 7
,
73
Overhaul the pump ..................................... 54
Index