REF.
33988/33989
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
INSTRUÇÕES IMPORTANTES DE SEGURANÇA / IMPORTANT SAFETY INSTRUCTIONS
-3-
comprenden los peligros que implica. Los niños no deben jugar con el aparato. La limpieza y el
mantenimiento a realizar por el usuario no deben realizarlos los niños sin supervisión.
21. El medio de desconexión de la toma de corriente posee una separación entre los contactos de
todas las clavijas que proporciona una desconexión completa y que debe incorporarse en el
cableado fijo de manera conforme con las normativas sobre cableado.
22. Consulte la sección “INSTALACIÓN” para saber cómo fijar e instalar el ventilador.
23. Consulte la sección “INFORMACIÓN SOBRE EL CABLE” para saber cómo conectar el cable.
24. Instrucciones sobre el reemplazo de la bombilla, incluido el modelo y referencia de la lámpara
Consulte la sección “Reemplazo de la bombilla”.
DESCRIPCIÓN DE SÍMBOLOS
Puede encontrar todos los símbolos relativos a esta lámpara tanto en el etiquetado del producto
como en la caja del embalaje.
Clase de aislamiento I Este ventilador debe conectarse con su toma de tierra (cable verde y
amarillo) al conductor de tierra.
Clase de aislamiento II Este ventilador cuenta con un doble aislamiento y no debe conectarse a
la toma de tierra.
CA - Corriente Alterna (Alternating Current Voltage)
Frecuencia (hercios)
Tensión en voltios
Intensidad de corriente en vatios
Distancia de separación mínima entre la lámpara y cualquier objeto inflamable en m.
Puede encontrar la distancia exacta en la etiqueta de la lámpara.
No utilice la lámpara sin el cristal. ¡Si este se estropea deberá ser cambiado por uno nuevo!
La lámpara está diseñada para emplear únicamente bombillas halógenas de tungsteno
autoprotegidas.
Uso exclusivo en espacios cerrados.
Grado de protección contra influencias externas. Puede encontrar el grado de protección
correspondiente en la etiqueta de la lámpara.
La luminaria no debe instalarse bajo ninguna circunstancia sobre una superficie normalmente
inflamable.
PUESTA EN FUNCIONAMIENTO
Conecte el suministro eléctrico y compruebe el funcionamiento del ventilador. La cadena de impul-
sos controla la velocidad del ventilador de la siguiente manera:
1 impulso - rápido; 2 impulsos - velocidad media; 3 impulsos - lento; 4 impulsos - apagado. Los
ajustes de velocidad para aumentar o disminuir la temperatura dependerán de factores como el
tamaño de la habitación, la altura de la habitación, el número de ventiladores disponibles, etc.
Mediante el interruptor deslizante puede controlar la dirección del ventilador, hacia delante o hacia
atrás.
Temperaturas cálidas/posición baja - (hacia delante) El ventilador gira en sentido contrario al de las
agujas del reloj. La corriente de aire dispuesta hacia abajo genera un efecto de refrigeración, como
se muestra en la figura A. Esto le permite colocar su aire acondicionado a una temperatura alta sin
tener que renunciar a su comodidad.
Temperaturas bajas/posición superior - (hacia detrás) El ventilador gira en el sentido de las agujas
del reloj.
Hz
V
W
3
15. This appliance can be used by children aged 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowladge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by
children without supervisions.
16. The means for disconnection from the supply mains
having a contact separation in all poles that provides full
disconnection that must be incorporated in the fixed wiring
in accordance with the wiring rules.
17. Regarding the instructions for the method of fixing and
how to install the fan, thanks to refer to the section
“INSTALLATION”.
18. Regarding the method of the cable connection, thanks to
refer to the section "CABLE INFORMATION".
Description of symbols:
You will find all the symbols related to his lamp on both the
product label and the box in which it came.
Insulation class I . This fan must be connected with its
ground wire (green and yellow cable) to the earthing
conductor.
Insulation class II . This fan has double insulation and it
must not be connected to the earth connection.
AC - Alternating Current Voltage
Frequency (hertz)
Voltage in volts
Intensity of current in watts
Exclusive use in enclosed spaces.
IP Level of protection against intrusion. You can find the
corresponding protection level on the label of the lamp.
The luminaire can under no circumstances be mounted
on normally flammable surfaces.
Switching it on
Connect to the power supply and check the functioning of
the fan. A series of pulses controls the speed of the fan, as
follows:
Press once - fast; press 2 times - medium speed; press 3
times - slow; press 4 times - off. The speed adjustments to
increase or reduce the temperature will depend on factors
4
/ Do not use the lamp without the glass. If it is
damaged, it must be replaced with a new one
The lamp is designed to use only self-protected tungsten
halogen light bulbs.
Exclusive use in enclosed spaces.
IP Level of protection against intrusion. You can find the
corresponding protection level on the label of the lamp.
The luminaire can under no circumstances be mounted
on normally flammable surfaces.
Switching it on
Connect to the power supply and check the functioning of
the fan. A series of pulses controls the speed of the fan, as
follows:
Press once - fast; press 2 times - medium speed; press 3
times - slow; press 4 times - off. The speed adjustments to
increase or reduce the temperature will depend on factors
such as the size of the room, its height, the number of fans
available, etc. Using the sliding switch, you can control the
direction of the fan, forward or backward.
Hot temperatures/low position - (forward) The fan turns
anti-clockwise. The downward air current creates a cooling
effect, as shown in figure A.
This enables you to set the air conditioning to a higher
temperature without compromising on comfort.
Low temperatures/upper position - (backward) The fan turns
clockwise. The upward air current causes the warm air in the
upper part of the room to move to other areas, as shown in
figure B.
This enables you to set the heating to a lower temperature
without compromising on comfort.
(Before using your fan in this position, consult point 10 of
the safety instructions).
NOTE: Switch the fan off and wait until it has stopped
completely before changing the position of the sliding
switch forward or backward.
Maintenance
1. Due to the normal movement of the fan, it is possible that
some connections may come lose. Check the support
connections, the supports and the attachment of the blades
twice a year. Make sure they are securely attached.
4
/ Do not use the lamp without the glass. If it is
damaged, it must be replaced with a new one
The lamp is designed to use only self-protected tungsten
halogen light bulbs.
Exclusive use in enclosed spaces.
IP Level of protection against intrusion. You can find the
corresponding protection level on the label of the lamp.
The luminaire can under no circumstances be mounted
on normally flammable surfaces.
Switching it on
Connect to the power supply and check the functioning of
the fan. A series of pulses controls the speed of the fan, as
follows:
Press once - fast; press 2 times - medium speed; press 3
times - slow; press 4 times - off. The speed adjustments to
increase or reduce the temperature will depend on factors
such as the size of the room, its height, the number of fans
available, etc. Using the sliding switch, you can control the
direction of the fan, forward or backward.
Hot temperatures/low position - (forward) The fan turns
anti-clockwise. The downward air current creates a cooling
effect, as shown in figure A.
This enables you to set the air conditioning to a higher
temperature without compromising on comfort.
Low temperatures/upper position - (backward) The fan turns
clockwise. The upward air current causes the warm air in the
upper part of the room to move to other areas, as shown in
figure B.
This enables you to set the heating to a lower temperature
without compromising on comfort.
(Before using your fan in this position, consult point 10 of
the safety instructions).
NOTE: Switch the fan off and wait until it has stopped
completely before changing the position of the sliding
switch forward or backward.
Maintenance
1. Due to the normal movement of the fan, it is possible that
some connections may come lose. Check the support
connections, the supports and the attachment of the blades
twice a year. Make sure they are securely attached.
4
/ Do not use the lamp without the glass. If it is
damaged, it must be replaced with a new one
The lamp is designed to use only self-protected tungsten
halogen light bulbs.
Exclusive use in enclosed spaces.
IP Level of protection against intrusion. You can find the
corresponding protection level on the label of the lamp.
The luminaire can under no circumstances be mounted
on normally flammable surfaces.
Switching it on
Connect to the power supply and check the functioning of
the fan. A series of pulses controls the speed of the fan, as
follows:
Press once - fast; press 2 times - medium speed; press 3
times - slow; press 4 times - off. The speed adjustments to
increase or reduce the temperature will depend on factors
such as the size of the room, its height, the number of fans
available, etc. Using the sliding switch, you can control the
direction of the fan, forward or backward.
Hot temperatures/low position - (forward) The fan turns
anti-clockwise. The downward air current creates a cooling
effect, as shown in figure A.
This enables you to set the air conditioning to a higher
temperature without compromising on comfort.
Low temperatures/upper position - (backward) The fan turns
clockwise. The upward air current causes the warm air in the
upper part of the room to move to other areas, as shown in
figure B.
This enables you to set the heating to a lower temperature
without compromising on comfort.
(Before using your fan in this position, consult point 10 of
the safety instructions).
NOTE: Switch the fan off and wait until it has stopped
completely before changing the position of the sliding
switch forward or backward.
Maintenance
1. Due to the normal movement of the fan, it is possible that
some connections may come lose. Check the support
connections, the supports and the attachment of the blades
twice a year. Make sure they are securely attached.
0,5m
IP