background image

17

High Accuracy Digital Multimeter with USB Interface

taken off the displayed value. When performing capacitance measurement, 
open the red and black testing line, press R

RE

EL

L  

∆∆

key to record the distributed 

capacitance, and after that performing capacitance measurement again, the 
distributed capacitance will have been taken off the displayed value. During 
relative measurement, analog bar is always indicating the present 
measurement value not the relative value. When measurement over, ‘OL’ will 
display instead of showing the relative value.

N

No

otte

es

s:: When going to relative value measurement under DC + AC mode, press 

‘R

RE

EL

L  

∆∆

’ immediately after the digits refresh.

3.13 Maximum Value/Minimum Value/Maximum-Minimum Value
Measurement

Except for frequency and diode measurements, by pressing the M

MA

AX

X/

/M

MIIN

N key the

meter will enter the maximum value record state. The meter measures the
present value and continuously judges if it is necessary to update the maximum
or minimum value. Pressing the M

MA

AX

X/

/M

MIIN

N key again will allow you to select the

minimum value. Press the M

MA

AX

X/

/M

MIIN

N key again to select the max-min value. The

analog bar ‘                              ‘ is always indicating the present measurement
value but not the MAX/MIN value. Press the M

MA

AX

X/

/M

MIIN

N key for 2 seconds and then

release it, the meter will exit the MAX/MIN record state. When measurement
over, ‘OL’ will display instead of showing the MAX/MIN value.

3.14 Backlight Control

Pressing the ‘L

LIIG

GH

HT

T’ key, the LCD display screens backlight will be lit and after 

30 seconds it will automatically go out. If you press the ‘L

LIIG

GH

HT

T’ key again while

the backlight is on, the backlight can be turned ‘off’ in advance. 
The backlight consumes 3x more battery power than in ordinary operation.

3.15 Data Hold

By pressing the ‘H

HO

OL

LD

D’ key it is possible to hold the measurement value and the

state at the moment of pressing the ‘H

HO

OL

LD

D’ key. When pressing the key again

data measurement will be resumed.

5163420K_Instructions.qxd  18/09/2009  12:57  Page 17

Summary of Contents for DAM100

























Reviews: