background image

INSTALLATION

5    INSTALLATION

5.1   INSTALLATION

Warning!

Hazardous voltage is present inside the device during operation. Disregarding of safety 

rules can result in severe personal injury or property damage.

Only qualified personnel may work with described devices after being familiar with warnings and 
safety notices in this paper and other safety regulations.

Following instruction must be taken into consideration:

The device must be accessible to qualified personnel only.

The device is permitted to operate in enclosed housing or cabinet only.

The device location must be vibration-free.

The admisible operating temperature must be observed.

Check the device for damage at unpacking. If device is damaged it must not be installed 
but it should be send to the manufacturer for repair.

The device should not be opened.

The device should be mounted on a 35 mm rail (acc to EN 50022).

Attach   ground   wire   before   attaching   power   supply.   Device   must   be   grounded   during 
operation!

Single core or stranded wire 0,5 – 2,5 mm

2

 must be used for power supply connection. If 

stranded wire is used, ferrules must be used to prevent fraying. Recommended stripping 
lenght is 5 mm.

Protective earthing wire must be terminated with tinned copper ear terminal.

The prescribed bending radius of the optical fibre cables must be observed.

Company:

Device:  

Document: 

Code:

Date:

Page:

Ediseja 21 CMU 100 / 1.5.S - 0

User manual CMUMU15S

01.09.2019

13

Summary of Contents for CMU 100 Series























Reviews: