Edimax PS-1208MFg User Manual Download

Page: 57 / 93

at the same time. When the MFP server starts up, it will auto-detect if the LAN

port is connected to an active network by an Ethernet cable. If the MFP server

is connected to an active network by Ethernet cable when starting up, the MFP

server will run in Ethernet mode. If the MFP server is not connected to an

active network by Ethernet cable when starting up, the MFP server will run in

wireless LAN mode. The MFP server default is in “Auto” mode.

ESSID

is the unique name identified by in a wireless LAN. The ID prevents the

unintentional merging of two co-located WLANs. Please make sure that the

ESSID of all stations and access points in the same WLAN network are the

same.

Channel Number

the channel of MFP server is fixed on channel 11

Summary of Contents for PS-1208MFg






























































































Search results

Summary of Contents for PS-1208MFg

Reviews:

Related manuals for PS-1208MFg

Brands by name

Popular brands

Edimax PS-1208MFg, User Manual

Search results

Summary of Contents for PS-1208MFg

Reviews:

Related manuals for PS-1208MFg

Brands by name

Popular brands