background image

1.

 

PRODUCT INSTALLATION 

I.

 

Install  the  switch  on  a  level  surface  that  can  support  the 
weight of the unit and the relevant components, and attach 
the rubber feet to the bottom. The rubber feet cushion the 
switch and helps protect the case from scratches. 

 
II.

 

Plug the switch into an electrical source with the provided power 
cord. 

 

Regarding the installation environment, we strongly recommend: 
 
1.

 

The switch should be placed in an appropriately ventilation 
environment. A minimum 25 mm space around the unit is 
recommended. 

2.

 

The switch and the relevant components should be kept away from 
sources of electrical noise such as radios, transmitters and 
broadband amplifiers. 

3.

 

Avoid environments with higher than recommended moisture levels. 

 

Troubleshooting 
 
1.

 

Power LED is not lit 

Check if the power cord is properly connected to the plug and the 
power outlet; make sure the power cord is firmly plugged into the 
power socket of the switch. 

 

2.

 

LINK/ACT LED is not lit when connected to devices 

 

Make sure the network device attached to the switch is turned on. 

 

Make sure the network cable is properly connected to the switch 
and the network device. 

 

Make sure the network cable is a UTP cable that complies with 
EIA/TIA 568 and Category 5 specifications. 

 

[!] Contact your dealer if problem persist. 

 

Summary of Contents for ES-1008PHE













Reviews: