background image

Federal Communication Commission Interference Statement 

 
This equipment has been tested and found to comply with the limits for a Class B 
digital device, pursuant to Part 15 of FCC Rules. These limits are designed to 
provide reasonable protection against harmful interference in a residential 
installation. This equipment generates, uses, and can radiate radio frequency 
energy and, if not installed and used in accordance with the instructions, may 
cause harmful interference to radio communications.     
However, there is no guarantee that interference will not occur in a particular 
installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and 
on, the user is encouraged to try to correct the interference by one or more of 
the following measures:     
1. Reorient or relocate the receiving antenna. 
2. Increase the separation between the equipment and receiver. 
3. Connect the equipment into an outlet on a circuit different from that to which 

the receiver is connected. 

4. Consult the dealer or an experienced radio technician for help. 
 

FCC Caution 

This device and its antenna must not be co-located or operating in conjunction 
with any other antenna or transmitter. 
This device complies with Part 15 of the FCC Rules. Operation is subject to the 
following two conditions: (1) this device may not cause harmful interference, and 
(2) this device must accept any interference received, including interference that 
may cause undesired operation. 
 Any changes or modifications not expressly approved by the party responsible 
for compliance could void the authority to operate equipment. 

 
CE Mark Warning 

This is a class B product. In a domestic environment this product may cause radio 
interference in which case the user may be required to take adequate measures.   

Summary of Contents for ES-1008PH









Reviews: