background image

1.

 

PRODUCT INSTALLATION 

 
There are two ways to install your switch, please select one that suits 
you. 
 

2.

 

Desktop Installation 

 
1. Install the switch on a level surface that can support the weight of 
the unit and the relevant components, and attach the rubber feet to 
the bottom. The rubber feet cushion the switch and helps protect the 
case from scratches. 
2. Plug the switch into an electrical source with the provided power cord. 
 

3.

 

Rack-Mount Installation 

 
Rack mounting allows for a more orderly installation when a 
series of network devices is being installed. 
 
1. Disconnect all the cables from the switch. 
2. Place the unit the right way up on a hard, flat surface with the front 
facing you. 
3. Position a mounting bracket over the mounting holes on one side of 
the unit. 
4. Insert the screws and fully tighten with a suitable screwdriver. 
5. Repeat the two previous steps for the other side of the unit. 
6. Insert the unit into the rack and secure with suitable screws 
7. Reconnect all the cables. 
 
Regarding the installation environment, we strongly recommend: 
 
1.

 

The switch should be placed in an appropriately ventilation environment.   
A minimum 25 mm space around the unit is recommended. 

2.

 

The switch and the relevant components should be kept away from sources 
of electrical noise such as radios, transmitters and broadband amplifiers. 

3.

 

Avoid environments with higher than recommended moisture levels. 

 
 
 

 

Summary of Contents for ES-1008PH









Reviews: