manualshive.com logo in svg

Edge MTP Tap Module, Installation And Testing, Page: 13 / 13

Share
Download
Edge MTP Tap Module Installation And Testing Download Page 13

Standard Recommended Procedure 003-128 | Issue 4 | September 2018 | Page 13 of 13

Corning Optical Communications LLC • PO Box 489 • Hickory, NC 28603-0489 USA 

800-743-2675 • FAX: 828-325-5060 • International: +1-828-901-5000 • www.corning.com/opcomm

Corning Optical Communications reserves the right to improve, enhance, and modify the features and specifications of Corning Optical Communications products without 

prior notification. A complete listing of the trademarks of Corning Optical Communications is available at www.corning.com/opcomm/trademarks. All other trademarks are 

the properties of their respective owners. Corning Optical Communications is ISO 9001 certified. © 2010, 2018 Corning Optical Communications. All rights reserved.

10 .4

.  To test the remaining portions of the system (Figure 17):

Step 1: 

Install the 

Light Source/RJ1 LC connector adapter

 onto LC number 2 of the harness plugged into the 

LIVE Port of the MTP Tap module. 

Step 2: 

Install 

Meter 1/RJ2’s LC connector

 into the number 1 port of the Edge module, Module “B”. 

Step 3: 

Install 

Meter 2/RJ3’s LC connector adapter 

onto LC number 1 of the harness plugged into the TAP port 

of the MTP Tap module.

Step 4: 

Continue testing through on the even fibers of the harness plugged into the front-mounted LIVE Port 

of the MTP Tap module using Tables 2 and 4 for testing sequences.

Figure 17 

Module harness

TAP port 

test harness

    

RJ1

    and 

    adapter

    

RJ2 

   

    

RJ3 

    and 

    adapter

   

Do NOT 

    disconnect

Pretium EDGE

  Module “B”

TPA-6141

multimode only

          

         

B

2

3

B

1

2
1

A

          

         M1

   

Do NOT 

    disconnect

0.00 dB

  Light 

 Source

     

“Near end”

“Far end”

B

6

12
11

A

B

5

10

9 

A

B

4

8
7

A

B

3

6

PnP

 Module

Part Number

Serial

MADE IN MEXICO

5

A

B

2

4
3

A

B

1

2
1

A

   W

AR

R

AN

TY

VOID

 MTP Tap Module “A”

Note:  Fiber loss

depends on length

 of system

 LC  #12

 LC  #2

          

         

          

         M2

   

Do NOT 

    disconnect

0.00 dB

 LC  #1

LIVE

LIVE

TAP

Summary of Contents for MTP Tap Module














Reviews:

No comments